Chicago Electric 94866 - Manuals

Page 2 - READ AND UNDERSTAND ALL INSTRUCTIONS; WORK AREA

PRODUCT SPECIFICATIONS SAVE THIS MANUAL You will need this manual for the safety warnings and precautions, assembly,operating, inspection, maintenance and cleaning procedures, parts list and as-sembly diagram. Keep your invoice with this manual. Write the invoice numberon the inside of the front cov...

Page 4 - TOOL USE AND CARE

12. Avoid accidental starting. Be sure the Power Switch is off before pluggingin. Carrying power tools with your finger on the Power Switch, or plugging inpower tools with the Power Switch on, invites accidents. 13. Remove adjusting keys or wrenches before turning the power tool on. Awrench or a key...

Page 5 - “Inspection, Maintenance, And Cleaning” section of this; SPECIFIC SAFETY RULES; SAVE THESE INSTRUCTIONS

23. Tool service must be performed only by qualified repair personnel. Serviceor maintenance performed by unqualified personnel could result in a risk of injury. 24. When servicing a tool, use only identical replacement parts. Followinstructions in the “Inspection, Maintenance, And Cleaning” section...

Page 7 - GROUNDING; GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

GROUNDING WARNING! GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS 1. Tools marked with “Grounding Required” have a three wire cord and three pronggrounding plug. The plug must be connected to a properly grounded outlet. Ifthe tool should electrically malfunction or break down, grounding provides a low...

Page 8 - EXTENSION CORDS; DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS; FIGURE B; THIS PRODUCT

EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated toolscan use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gaugeextension cord. Using extension cords with inadequately sized wire causes a...

Page 9 - RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*; FIGURE C; SYMBOLOGY; FIGURE D

6. If you are using an extension cord outdoors, make sure it is marked with thesuffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition.Always replace a damaged extension cord or have it repaired by...

Page 10 - To Assemble The Blower Unit:

UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 14are included. If any parts are missing or broken, please call Harbor Freight Tools at thenumber shown on the cover of this manual as soon as possible. ASSEMBLY INSTRUCTIONS 1. CAUTION! Always make sure the P...

Page 11 - OPERATING INSTRUCTIONS; To Operate The Blower:

SKU 94866 For technical questions, please call 1-800-444-3353 PAGE 11 To Assemble The Vacuum Unit: 1. Remove the Protection Cover (7) by turning it counterclockwise. (See Figure F.) 2. Insert the Vacuum Pipe Center Piece (8) onto the Housing (14). Then, turn theVacuum Pipe Center Piece clockwise to ...

Page 12 - To Operate The Vacuum:; Move the Vacuum slowly and evenly; FIGURE G

SKU 94866 For technical questions, please call 1-800-444-3353 PAGE 12 move the unit slowly and evenly. (See Figure G.) To Operate The Vacuum: 1. Make sure to remove the Protection Cover (7). Also, make sure the VacuumBag (11) is properly connected to the unit and its Shoulder Strap is properlyadjust...

Page 13 - TROUBLESHOOTING

INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Make sure the Power Switch (4) of the Blower/Vacuum is in its“OFF” position and the tool is unplugged from its electrical outlet beforeperforming any inspection, maintenance, or cleaning procedures. 2. Before each use: Inspect the general condition o...

Page 14 - PARTS LIST AND ASSEMBLY DIAGRAM; PLEASE READ THE FOLLOWING CAREFULLY

PARTS LIST AND ASSEMBLY DIAGRAM NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 94866 For technical questions, please call 1-800-444-3353 PAGE 14 7 2 3 4 5 1 3 1 1 2 6 1 0 1 1 8 9 1 3 1 4 1 4 Part # Description Qty. P...

Page 15 - WARRANTY; LIMITED 90 DAY WARRANTY

WARRANTY SKU 94866 For technical questions, please call 1-800-444-3353 PAGE 15 Harbor Freight Tools Co. makes ever y effort to assure that its products meet high quality and durability standards,and warrants to the original purchaser that this product is free from def ects in materials and wor kmans...