Chicago Electric 93213 - Manuals

Page 2 - SAVE THIS MANuAL; IMPORTANT SAFETY; SAFETY WARNINgS ANd; presence of flammable gases or liquids.

Page 2 For technical questions, please call 1-800-444-3353. SKU 93213 SAVE THIS MANuAL Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram...

Page 3 - influence of alcohol or drugs.; determine if your judgment or reflexes; Sharpener around flammable

Page 3 For technical questions, please call 1-800-444-3353. SKU 93213 attachment to do the work of a larger industrial tool. There are certain applications for which this tool was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this tool and d...

Page 4 - Electromagnetic fields in close proximity; grinding Wheel Warnings; Only use grinding wheels that fit the

Page 4 For technical questions, please call 1-800-444-3353. SKU 93213 processes) can result in eye, skin and breathing irritation. Always use a NIOSH (National Institute for Occupational Safety and Health) approved respirator and safety goggles. Avoid skin exposure.People with pacemakers should 24. ...

Page 5 - gROuNdINg; Check with a qualified electrician; grounded Tools: Tools with Three; satisfies OSHA requirements and

Page 5 For technical questions, please call 1-800-444-3353. SKU 93213 gROuNdINg TO PREVENT ELECTRIC SHOCK ANd dEATH FROM INCORRECT gROuNdINg WIRE CONNECTION: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. do not modify the power cord plug provid...

Page 6 - Extension Cords; Grounded; Symbology

Page 6 For technical questions, please call 1-800-444-3353. SKU 93213 Extension Cords Grounded 1. tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord.As the distance from the supply outlet 2. increases, you must use a heavier gauge exte...

Page 7 - SPECIFICATIONS; uNPACKINg

Page 7 For technical questions, please call 1-800-444-3353. SKU 93213 SPECIFICATIONS Motor 120 V~, 0.75 A (Load), Direct Drive RPM 4200 Vise Capacity 0.80” to 0.50” Table / Vise Angles 35° Right to LeftArbor Diameter 7/8” Wheel Dimensions 4-1/4” Dia. x 1/8” ThickWorking time S3:10S ON / 15S OFF Note...

Page 8 - ASSEMBLY; Installation; FIguRE 1

Page 8 For technical questions, please call 1-800-444-3353. SKU 93213 ASSEMBLY WARNINg! Unplug the tool before changing grinding wheels, or before making any adjustments to the tool. Installation Install the Sharpener to a workbench 1. before use. FIguRE 1 1/4” Hole with Bolt Lock Wheel (18) 1. When...

Page 9 - Mounting a grinding Wheel; FIguRE 3

Page 9 For technical questions, please call 1-800-444-3353. SKU 93213 Mounting a grinding Wheel Refer to the Assembly Drawing on page 10. FIguRE 3 Lock Stop (6) Top Housing (4B) grinding Wheel Cover (11B) 1. Raise the Top Housing (4B) and lock it in the up position by tightening the Lock Stop (6). R...

Page 10 - OPERATION; Wash it with a nonflammable solvent. Do; FIguRE 6; FIguRE 5

Page 10 For technical questions, please call 1-800-444-3353. SKU 93213 OPERATION WARNINg! Unplug the unit before adjusting chain to be sharpened. Refer to the Assembly Drawing on page 10 and the various photographs. Note: Raise the Top Housing (4B) while adjusting the chain.Clean the chain before sh...

Page 11 - Sharpening

Page 11 For technical questions, please call 1-800-444-3353. SKU 93213 FIguRE 7 Lock Stop (6) 6. Hold it at that position while you tighten the Lock Stop (6) so that the wheel will only go down to that point. See FIguRE 7 . Depending on the amount of material 7. you wish to remove, tighten or loosen...

Page 12 - After you finished sharpening all of the; See FIguRE; the angle so that the first tooth that

Page 12 For technical questions, please call 1-800-444-3353. SKU 93213 FIguRE 10 3. Slowly lower the grinding wheel as shown in FIguRE 10 . If you notice slight errors in your settings, turn off the unit and unplug it before you make your adjustments. Note: A good grind occurs when the contact betwe...

Page 13 - MAINTENANCE

Page 13 For technical questions, please call 1-800-444-3353. SKU 93213 MAINTENANCE Keep the Sharpener clean and free of 1. dust, metal debris and dirt.Check the Grinding Wheel before each 2. use to make sure it isn’t damaged. Do not use a grinding wheel if it is chipped, cracked, or worn. You can ch...

Page 14 - PARTS LIST; PLEASE REAd THE FOLLOWINg CAREFuLLY; individually as replacement parts.

Page 14 For technical questions, please call 1-800-444-3353. SKU 93213 PARTS LIST Part description Q’ty 1 Screw 3 2 Motor Cover 1 3 Power Cord 1 4B Top Housing 1 5B Rocker Switch 1 6 Lock Stop 1 7 Grinding Wheel Base 1 8 Grinding Wheel 1 9 Grinder Lock Cap 1 10 Screw 2 11B Grinding Wheel Cover 1 12 ...

Page 15 - ASSEMBLY dRAWINg; Chain Mounting Assembly Set

Page 15 For technical questions, please call 1-800-444-3353. SKU 93213 ASSEMBLY dRAWINg Chain Mounting Assembly Set 39

Page 16 - LIMITEd 90 dAY WARRANTY; THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

Page 16 For technical questions, please call 1-800-444-3353. SKU 93213 LIMITEd 90 dAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in material...