Chicago Electric 67616 - Manuals

Page 2 - save this manual; impOrtant saFetY; general power tool safety Warnings; The term ′′power tool′′ in the warnings; the presence of flammable liquids,; sparks which may ignite the dust or

Page 2 For technical questions, please call 1-800-444-3353. SKU 67616 save this manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram...

Page 3 - under the influence of drugs, alcohol; Safety

Page 3 For technical questions, please call 1-800-444-3353. SKU 67616 ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. do not expose power tools to rain c. or wet conditions. Water entering a power tool will increase the risk of electric shock. do not ...

Page 4 - qualified repair person using only; drill and impact drill safety; maintain a firm grip on the tool with both

Page 4 For technical questions, please call 1-800-444-3353. SKU 67616 with the switch is dangerous and must be repaired. disconnect the plug from the power c. source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventi...

Page 5 - vibration safety

Page 5 For technical questions, please call 1-800-444-3353. SKU 67616 pacemaker interference or pacemaker failure. In addition, people with pacemakers should: • Avoid operating alone. • Do not use with power switch locked on. • Properly maintain and inspect to avoid electrical shock. • Any power cor...

Page 6 - save these; grOunding; Check with a qualified electrician; double insulated tools: tools with; double insulation system which satisfies; extension cords; Grounded

Page 6 For technical questions, please call 1-800-444-3353. SKU 67616 To reduce vibration, maintain the tool 7. as explained in this manual. If any abnormal vibration occurs, stop use immediately. save these instructiOns. grOunding tO prevent electric shOcK and death FrOm incOrrect grOunding Wire cO...

Page 7 - symbology

Page 7 For technical questions, please call 1-800-444-3353. SKU 67616 Make sure the extension cord is properly 7. wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it.Protect the extension cords from sharp 8. o...

Page 8 - assembly; Clamping Band will enable the two tabs; Operating instructiOns; tool set up

Page 8 For technical questions, please call 1-800-444-3353. SKU 67616 speciFicatiOns Electrical Input 120 V~ / 60 Hz / 6.5 A (Rated) Motor Speed 0-2500 RPM / 0-41,600 BPM Drilling Capacity 1/2” in Steel 5/8” in Concrete 1” in Wood (Hammer Drill and Drill mode) Chuck Capacity 1/16” to 1/2”, plus Key ...

Page 9 - Gauge into gauge slot and re-tighten

Page 9 For technical questions, please call 1-800-444-3353. SKU 67616 and unplug the tool from its electrical outlet before adjusting tool or installing accessories. The Hammer Drill is equipped with a keyed Chuck. Follow these steps to insert bit: Insert the Chuck Key (52) into the Chuck 1. and tur...

Page 10 - After pressing Trigger, press Lock Button; Warning! use this function OnlY; metal drilling tips; a larger bit for the final size hole.; Wood drilling tips

Page 10 For technical questions, please call 1-800-444-3353. SKU 67616 oscillating hammer motion), slide the Mode Switch (21) to left or right. The “drill” symbol indicates plain drilling while the “hammer” symbol indicates hammer drilling. See Figure 3. Figure 3 Mode Switch (21) (Top View) Drill sy...

Page 11 - recommended drill bits sets; sKu

Page 11 For technical questions, please call 1-800-444-3353. SKU 67616 recommended drill bits sets The chart below lists applicable Drill Bit sets that are available from Harbor Freight Tools. sKu name application sizes 32925 29-Piece High Speed Steel Drill Bit Set For Metal drilling 1/16” to 1/2” b...

Page 12 - Procedures not specifically; lubrication; replaced only by a qualified service

Page 12 For technical questions, please call 1-800-444-3353. SKU 67616 maintenance and servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. tO prevent seriOus injurY FrOm accidental OperatiOn: turn the power switch of the tool off and unplu...

Page 13 - troubleshooting; problem; disconnect power supply before service.

Page 13 For technical questions, please call 1-800-444-3353. SKU 67616 troubleshooting problem possible causes likely solutions Tool will not start. Cord not connected. 1. No power at outlet. 2. Tool’s thermal reset breaker tripped 3. (if equipped).Internal damage or wear. (Carbon 4. brushes or swit...

Page 14 - please read the FOllOWing careFullY; parts list; individually as replacement parts.

Page 14 For technical questions, please call 1-800-444-3353. SKU 67616 part description Qty. 1 Depth Gauge 1 2 Clamping Band 1 3 Hex Bolt (M8x110) 1 4 Auxiliary Handle 1 5 Hex Nut (M8) 1 6 Left Head Screw (M6x22) 1 7 Drill Chuck 1 8 Spindle 1 9 Tapping Screw (ST4x22) 4 10 Spring (Ø18.2x9) 1 11 Gear ...

Page 15 - assemblY diagram

Page 15 For technical questions, please call 1-800-444-3353. SKU 67616 assemblY diagram 54 55 56 43

Page 16 - limited 90 daY WarrantY; ExPRESSLy IN LIEU OF ALL OTHER

Page 16 For technical questions, please call 1-800-444-3353. SKU 67616 limited 90 daY WarrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in material...