Chicago Electric 67119 - Manuals

Chicago Electric 67119 – Manual in PDF format online.

Manuals:

Manual

Manual Chicago Electric 67119

Summary

Page 2 - contentS; imPoRtant SaFetY

SKU 67119 For technical questions, please call 1-800-444-3353. Page 2 contentS imPoRtant SaFetY inFoRmation ............................ 3 geneRal PoweR tool SaFetY waRningS....................... 3 Plunge RouteR SaFetY waRningS ...................................... 5 VibRation SaFetY ................

Page 3 - SaVe tHiS manual; general Power tool Safety; The term ′′power tool′′ in the

SKU 67119 For technical questions, please call 1-800-444-3353. Page 3 SaVe tHiS manual Keep this manual for the safety warn- ings and precautions, assembly, operat- ing, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly dia...

Page 5 - Plunge Router Safety warnings; Use only accessories rated at least

SKU 67119 For technical questions, please call 1-800-444-3353. Page 5 Power tool use and care 4. do not force the power tool. use a. the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. do not use the power tool i...

Page 7 - Vibration Safety

SKU 67119 For technical questions, please call 1-800-444-3353. Page 7 • Do not use with power switch locked on. • Properly maintain and inspect to avoid electrical shock. • Any power cord must be properly grounded. Ground Fault Circuit Inter- rupter (GFCI) should also be imple- mented – it prevents ...

Page 8 - SaVe tHeSe; gRounding; grounded tools: tools with three

SKU 67119 For technical questions, please call 1-800-444-3353. Page 8 Grip tool as lightly as possible (while 6. still keeping safe control of it). Let the tool do the work.To reduce vibration, maintain the tool 7. as explained in this manual. If any abnormal vibration occurs, stop use immediately. ...

Page 9 - outlets for 2-Prong Plug; which satisfies OSHA requirements; extension cords; Grounded

SKU 67119 For technical questions, please call 1-800-444-3353. Page 9 double insulated tools: tools with two Prong Plugs outlets for 2-Prong Plug Tools marked “Double Insulated” do 1. not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies w...

Page 10 - Symbology

SKU 67119 For technical questions, please call 1-800-444-3353. Page 10 Recommended minimum wiRe gauge FoR extenSion coRdS* (120/240 Volt) namePlate amPeReS (at full load) extenSion coRd lengtH 25’ 50’ 75’ 100’ 150’ 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18...

Page 11 - Functions

SKU 67119 For technical questions, please call 1-800-444-3353. Page 11 SPeciFicationS Power 1-1/2 HP Electrical Input 120 V~ / 60 Hz / 10 A Motor Speed 11,000 - 28,000 RPM (No Load) Collet Capacity 1/4” Maximum Plunge 2-1/8” Depth Measurements 1/16” increments Depth Stop 4-stage turret stop e194601 ...

Page 12 - oPeRating inStRuctionS; tool Set up

SKU 67119 For technical questions, please call 1-800-444-3353. Page 12 oPeRating inStRuctionS Read the entiRe imPoRtant SaFetY inFoRmation section at the beginning of this manual including all text under subheadings therein before set up or use of this product. tool Set up to PReVent SeRiouS injuRY ...

Page 13 - Figure 4; in fine increments by turning the; edge guide; Figure 5

SKU 67119 For technical questions, please call 1-800-444-3353. Page 13 Loosen the Thumb Screw so that the 1. Depth Stop Bar (30) can slide freely.Rotate the Adjusting Knob (26) until 2. the Depth Adjusting Bolt (29) pro- trudes about 1/4” from the Depth Stop Bar.Rotate the Depth Stop Bar to the left...

Page 14 - Hold Router handles firmly with both; general operating instructions; each progressive pass, until the final

SKU 67119 For technical questions, please call 1-800-444-3353. Page 14 Slide the bars on the Edge Guide b. into the slots on the Base of the Router with the fence facing the workpiece. note: The Edge Guide can be inserted into either side of the tool to make cuts along the left or right side of the ...

Page 16 - lubrication

SKU 67119 For technical questions, please call 1-800-444-3353. Page 16 maintenance and SeRVicing Procedures not specifically explained in this manual must be performed only by a qualified technician. to PReVent SeRiouS injuRY FRom accidental oPeRation: turn the Power Switch of the tool off and unplu...

Page 17 - troubleshooting; Problem; tool. disconnect power supply before service.; PleaSe Read tHe Following caReFullY

SKU 67119 For technical questions, please call 1-800-444-3353. Page 17 troubleshooting Problem Possible causes likely Solutions Tool will not start. Cord not connected. 1. No power at outlet. 2. Tool’s thermal reset breaker 3. tripped (if equipped).Internal damage or wear. 4. (Carbon brushes or swit...

Page 18 - PaRtS liSt

SKU 67119 For technical questions, please call 1-800-444-3353. Page 18 Part description Qty 1 Tapping Screw 8 2 Cover 1 3 Screw 2 4 Speed Adjuster 1 5 Tapping Screw 5 6 Tapping Screw 2 7 Cover 1 8 Cover 1 9 Tapping Screw 2 10 Epoxy Board 2 11 Brush Holder 2 12 Carbon Brush 2 13 Motor Housing 1 14 Sp...

Page 19 - aSSemblY diagRam; able individually as replacement parts.

SKU 67119 For technical questions, please call 1-800-444-3353. Page 19 aSSemblY diagRam Record Product’s Serial number Here: note: If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not avail- able...

Page 20 - limited 90 daY waRRantY; WARRANTIES OF MERCHANTABILITY AND FITNESS.

SKU 67119 For technical questions, please call 1-800-444-3353. Page 20 limited 90 daY waRRantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this prod- uct is free from defects in materi...