Chicago Electric 40315 - Manuals

Chicago Electric 40315 – Manual in PDF format online.

Manuals:

Manual

Manual Chicago Electric 40315

Summary

Page 2 - SAVE THIS MANUAL; IMPORTANT SAFETY; General Power Tool Safety

Page 2 SKU 40315 For technical questions, please call 1-800-444-3353. SAVE THIS MANUAL Keep this manual for the safety warn- ings and precautions, assembly, operat- ing, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly dia...

Page 4 - Vibration Safety

Page 4 SKU 40315 For technical questions, please call 1-800-444-3353. do the job better and safer at the rate for which it was designed. b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be con- trolled with the switch is dangerous and must be repaire...

Page 5 - SPECIFIC SAFETY WARNINGS

Page 5 SKU 40315 For technical questions, please call 1-800-444-3353. 4. Use tools with the lowest vibration when there is a choice between dif- ferent processes. 5. Include vibration-free periods each day of work. 6. Grip tool as lightly as possible (while still keeping safe control of it). Let the...

Page 6 - TILE SAW; does

Page 6 SKU 40315 For technical questions, please call 1-800-444-3353. 14. POWER CORD 120 VOLT, GROUNDED ELECTRICAL OUTLET TILE SAW DRIP LOOP Figure 1 Always arrange a “drip loop” in the Power Cord/Plug (34) connecting the Tile Saw to a 120 volt, ground- ed, electrical outlet. A drip loop is that par...

Page 9 - SAVE THESE

Page 9 SKU 40315 For technical questions, please call 1-800-444-3353. cause injury beyond immediate area of operation. 11. Position the cord clear of the spin- ning blade. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory. Avoid uninte...

Page 10 - GROUNDING; Grounded Tools: Tools with Three

Page 10 SKU 40315 For technical questions, please call 1-800-444-3353. GROUNDING TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provi...

Page 11 - Extension Cords; Grounded; Symbology

Page 11 SKU 40315 For technical questions, please call 1-800-444-3353. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Extension Cords 1. Grounded tools require a three wire extension cord. Double Insulated ...

Page 12 - Assembly; To Permanently Mount Tile Saw On A

Page 12 SKU 40315 For technical questions, please call 1-800-444-3353. SPECIFICATIONS Blade Diameter (Blade Not Included, Sold Separately) 7" (67393 7” Continuous Rim Diamond Blade Recommended) Arbor Diameter 1" Maximum Cutting Capacity 1” Thick, 12” Wide Electrical Requirements 120 V~ / 60 ...

Page 13 - FIGURE 2

Page 13 SKU 40315 For technical questions, please call 1-800-444-3353. ing sure no hidden electric cords or cables are in the drilling path. 6. Once the mounting holes are drilled, align the four 7/16” wide x 3-1/2” long mounting slots in the base of the Inner Cover (16) with the four pre- drilled m...

Page 14 - OPERATING INSTRUCTIONS; Tool Set Up

Page 14 SKU 40315 For technical questions, please call 1-800-444-3353. OPERATING INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up TO PREVENT SERIOUS INJURY ...

Page 15 - General Operating Instructions; width; Put on ANSI-approved safety

Page 15 SKU 40315 For technical questions, please call 1-800-444-3353. General Operating Instructions 1. Fill Tray (17) with water and carefully slide Tray under Blade. Make sure water level is deep enough to cover lower edge of Cutting Wheel Blade, but not so deep as to spill over edge of Tray. (Se...

Page 16 - Lubrication

Page 16 SKU 40315 For technical questions, please call 1-800-444-3353. MAINTENANCE AND SERVICING Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool to its “OFF” ...

Page 17 - Troubleshooting; Problem; PLEASE READ THE FOLLOWING CAREFULLY

Page 17 SKU 40315 For technical questions, please call 1-800-444-3353. (not included, sold separately), making sure to install Blade according to indicated rotation direction on Blade. F. Replace the Outside Flange (7) and Nut (4). Use the Spanner (59) to hold the Outside Flange (7) while you tighte...

Page 18 - PARTS LIST

Page 18 SKU 40315 For technical questions, please call 1-800-444-3353. PARTS LIST Part Description Part Description Part Description 1 Front Cover 21 Power Switch 41 Motor Lead Wire 2 Screw (M4x10) 22 Switch Seal 42 Motor 3 Washer (M4) 23 Switch Cover 43 Rear Cover 4 Nut (M12) 24 Inlet Clip 44 Handl...

Page 19 - ASSEMBLY DIAGRAM

Page 19 SKU 40315 For technical questions, please call 1-800-444-3353. ASSEMBLY DIAGRAM Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available i...

Page 20 - 0 Day Warranty; IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

Page 20 SKU 40315 For technical questions, please call 1-800-444-3353. 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and wo...