Char-Broil 463250510 - Manuals

WARNING If “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department! Connecting Regulator to the LP Cylinder 1. LP cylinder must be properly secured onto grill. (Refer to assembly section.) 2. Turn all control knobs to the OFF position. 3. Turn ...

6. Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in some resistance. An additional one-half to three-quarters turn is required to complete the connection. Tighten by hand only – do not use tools. NOTE...

WARNING For Safe Use of Your Grill and to Avoid Serious Injury:• Do not let children operate or play near grill. • Keep grill area clear and free from materials that burn. • Do not block holes in sides or back of grill. • Check burner flames regularly. • Use grill only in well-ventilated space. NEVE...

Ignitor Check •Turn gas off at LP cylinder. Press and hold electronic ignitor button. "Click" should be heard and spark seen each time between each collector box or burner and electrode. See "Troubleshooting" if no click or spark. Valve Check •Important: Make sure gas is off at LP cy...

CAUTION Storing Your Grill •Clean cooking grates.•Store in dry location.•When LP cylinder is connected to grill, store outdoors in a well- ventilated space and out of reach of children. •Cover grill if stored outdoors. Choose from a variety of grill covers offered by manufacturer. •Store grill indoo...

This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated...

PARTS LIST 11 NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the method of assembly remains the same. Not Pictured: Key Qty Description … 2 DOOR MAGNET … 1 W RENCH, F/ CASTERS … 1 HARDW ARE PACK … 1 ASSEMBLY MA...

PARTS DIAGRAM 12 A TT W J B C P QQ RR RR RR SS T R G G H D D E I Y S U U U U O O O Q V V V V CC X XX YY ZZ EE GG GG VV UU MM HH PP OO Z AA AAA NN DD JJ II LL KK WW FF BB BBB L N K M F

13 ASSEMBLY 2 1/4-20x1/2” screw 1 Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers per panel. IMPORTANT: Panel with large hole must be on left side of bottom shelf. 7mm lock washer 7mm flat washer Locking caster Bottom shelf Fixed caster Rear ...

14 3 4 This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of grill head with posts on cart side panels. Make sure the regulator hose is hanging outside the cart. Grill head must face open side of cart. Place...

15 6 5 On back of grill, place upper back panel between side panels and above lower back panel. Secure upper back panel, in lower holes, using one 1/4-20x1½” screw, 7mm lock washer, and 7mm flat washer on each side. Do not fully tighten screws until side shelf installation is complete in later steps...

16 7 Attach right side fascia to right side shelf using four #10-24x3/8” screws, 5mm lock washers and 5mm flat washers, shown A. Attach one 1/4-20x1-1/2” screw, one 1/4-20x1/2” screw ,two 7mm lock washers and two 7mm flat washers at the rear shelf, shown C. Attach three 1/4-20x1/2” screw, 7mm lock w...

8 17 left side shelf Attach left side fascia to left side shelf using four #10-24x3/8” screws, 5mm lock washers and 5mm flat washers, shown A. Attach one Attach three 1/4-20x1/2” screws, 7mm lock washers, 7mm flat washers at the front shelf, shown D. 1/4-20x1-1/2” screw,one 1/4-20x1/2” screw,two 7mm...

9 18 Position sideburner valve bracket beneath sideburner shelf fascia so that valve stem comes through larger center hole in fascia. Align the holes on valve bracket with left and right holes on fascia. Secure using screws and lock washers that were removed from bracket, shown A. Attach sideburner ...

11 20 12 Inside of cart, insert rear tank heat shield tabs(w/o holes) into slots on the bottom of upper back panel. Attach FireBox lower heat shield to the tank heat shield using two #8x3/8” self-tapping screws, shown A. Attach front tank heat shield tabs(w/ holes) under front brace using two #8x3/8...

13 21 Insert the pin on bottom of doors into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top of Align the trough pins with the holes on fire box. Make sure trough is put in the right direction. Place trough onto fire box. door, and release hinge pin into door. pin...

15 22 Place cooking grates onto the firebox as shown. Place the Warming Rack onto the the firebox. Make sure insert the Warming Rack ends into the holes properly as shown. Cooking Grate Warming Rack Tank Screw at rear of cart CAUTION LP Tank valve must face to front of cart once tank is attached. Fa...

EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Problem Gas leaking from cracked/cut/burned hose. Gas leaking from LP cylinder. Gas leaking from LP cylinder valve. Gas leaking between LP cylinder and regulator connection. Fire ...

Troubleshooting ( continued ) Problem Burner(s) will not light using ignitor. Burner(s) will notmatch light. Sudden drop in gasflow or low flame. Flames blow out. Flare-up. Persistent grease fire. Flashback...(fire in burner tube(s)). Unable to fill LP tank. One burner does not light from other burn...

Troubleshooting - Integrated Electronic Ignition Problem (Ignition) SECTION I No sparks appear at any electrodes when burner control knobs are turned to ; no noise can be heard from spark module. SECTION II No sparks appear at any electrodes when burner control knobs are turned to ; noise can be hea...