Page 2 - I. INSTALLATION INSTRUCTIONS; When the oven arrives, it should consist of:; INDEX; Section
I. INSTALLATION INSTRUCTIONS Section Item Page A Receiving 2 B Set Up / Mounting 2 C Installation with Casters (Optional) 3 D Location & Minimum Clearances 4 E Gas Connections 4 F Electrical Connection 5 G Flue Connection Ventilation 5 H Burner Operation 5 I System Check Rotary Control 5 J Progr...
Page 3 - Assembly Instructions; : Place undershelf between; Oven Base
3 For a single unit: Refer to Figure 4 (1) Tilt Oven over to left-hand side and attach two 31” legs on the right-hand side with three ½” bolts and washers. Tighten firmly. (2) Using proper lifting equipment, lift up the left-hand side and attach two 31” legs on the left-hand side the same way. For a...
Page 4 - D. LOCATION AND MINIMUM CLEARANCES:; Under Ventilation Hood; No external regulator is required.; Gas Type Supply Pressure; 0 or 50 mbar depending on country
D. LOCATION AND MINIMUM CLEARANCES: Move the oven to its final location keeping the minimum clearance from the back of the oven to the wall. This clearance is necessary for safe operation and to provide proper air flow to the burner chamber. MINIMUM CLEARANCES FROM COMBUSTIBLE AND NONCOMBUSTIBLE CON...
Page 5 - Open the oven door.
F. ELECTRICAL CONNECTION: The oven, when installed, must be electrically grounded in accordance with local codes and/or the latest edition of the National Electrical Code ANSI/NFPA No. 70 in the USA (Canadian Electrical Code CSA Standard C22.1, Part 1 in Canada). In Europe, the appliance must be con...
Page 6 - II. OPERATING INSTRUCTIONS; B. OPERATION SEQUENCE ROTARY CONTROL:
(5) Turn Gas Cock Dial to “ON” position (only for USA and Canada). (6) Turn the thermostat knob. The indicator light near the thermostat will illuminate and the burners will come on. (7) Turn the Timer Knob and set a time of 2 minutes. At the end of 2 minutes, you should hear the buzzer. Turn the ti...
Page 9 - Figure 3 Stacking Instructions For: COB-G & COM-G Convection Ovens; ITEM 1; Blower Wheel; Cleaning The Blower Wheel
Figure 3 Stacking Instructions For: COB-G & COM-G Convection Ovens ITEM 1 ITEM 2 ITEM 3 E3770A E3771A 3/8”-16 Bolt 9 Wheel Puller Bolt 3/8”-Hex Blower Wheel Set Screws (2) Motor Cleaning The Blower Wheel Figure 2 Attach part # 21818062 with 6 each 8-32 stainless screws Material: 14 ga 201 Stainl...
Page 10 - Foot Insert, Adjustable; Item
10 WITH PLATE CASTER WITHOUT PLATE CASTER Figure 4 LEG ASSEMBLY INSTRUCTIONS - MODEL: COB-G & COM-G 1. Attach four item 2 to four item 1 using item 3, 4 and 5. 2. Using proper lifting equipment attach item 1 to the corresponding hole patterns located in the bottom of the oven with item 6. 1 2179...
Page 11 - FAN; MOT; COM
11 Single-Phase 120V Wiring Diagram (Push-Button Control) GROUND STUD T2 T3 T4 T5 T1 T8 T9 T7 T6 T12 T13 T1 1 T10 DOOR SWITCH PROBE 37 39 LIGHTS 120V LOW HIGH 120V 24V PROBE IGNITER FLAME SENSOR TRANSFORMER RELA Y 4 POSTION DOOR SWITCH POWER SWITCH PUSH BUTT ON SWITCH CH104 CONTROL COMBINA TION VA L...
Page 12 - HIGH
12 Single-Phase 120V Wiring Diagram (Dial Control) BLACK P1 P2 P3 P4 COM NC NO T6 T7 T8 T9 T10 T1 1 BLUE 4 1 2 3 YELLOW GROUND STUD POWER LIGHT T- S TA T LIGHT SWITCH LIGHTS BUZZER 60 MIN TIMER POWER SWITCH DOOR SWITCH FLAME SENSOR IGNITER HIGH LOW CENTRIFUGAL SWITCH FAN MOTOR COM 120V WHITE GROUND ...
Page 13 - PARTS LIST; Natural L.P. Other; Serial; Full Size Gas Convection Oven
13 PARTS LIST Model Number: COB-G & COM-G Type of Gas: Natural L.P. Other 4/05 Note: When ordering, ALWAYS specify Part #, Model #, Serial #,Voltage/Phase & type of Gas. Serial Number: Voltage/Phase: 115/1 208-240/1 230/1 (CE) COB-G & COM-G Full Size Gas Convection Oven PO Box 80400 * Si...
Page 14 - Page
14 Exterior / Interior / Controls / Doors 4/05 Note: When ordering, AL W A YS specify Part #, Model #, Serial #, V oltage/Phase & type of Gas. Page 2 of 4 (Not Shown) E8752A Kit, 25" Legs Black W/3" Adj Feet E8753A Kit, 25" Legs Black W/Plate Caster E8754A Kit, 25" Legs S/S W/3...
Page 16 - BKI LIMITED WARRANTY
16 WHAT IS COVERED This warranty covers defects in material and workmanship under normal use, and applies only to the original purchaser providing that: ♦ The equipment has not been accidentally or intentionally damaged, altered or misused; ♦ The equipment is properly installed, adjusted, operated a...