Page 3 - Support
Australia/New Zealand This digital equipment fulfills the requirements for RFemission according to the Class A limit of AS/NZS CISPR 22.The product shall be connected using a shielded networkcable (STP) that is properly grounded. Notice! This is aClass A product. In a domestic environment this produ...
Page 5 - Safety Information; Hazard Levels; DANGER; Other Message Levels; IS
AXIS Q604 Series Safety Information Read through this Installation Guide carefully before installing the product. Keep the InstallationGuide for future reference. Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result indeath or serious injury. WARNING Indicates a ha...
Page 6 - Safety Instructions; WARNING; Transportation
AXIS Q604 Series Safety Instructions WARNING • The Axis product shall be installed by a trained professional. NO NO NOTICE TICE TICE • The Axis product shall be used in compliance with local laws and regulations. • To use the Axis product outdoors, or in similar environments, it shall be installed i...
Page 7 - Dome Cover
AXIS Q604 Series WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. • Dispose of used batteries according to local regulations or the battery manufacturer's instructions. Dome Cover NO NO NOTICE TICE...
Page 9 - Installation Guide; Installation Steps
AXIS Q604 Series Installation Guide This Installation Guide provides instructions for installing AXIS Q6042/Q6044/Q6045 Mk II PTZDome Network Camera on your network. For other aspects of using the product, see the UserManual available at www.axis.com Installation Steps 1. Make sure the package conte...
Page 10 - Hardware Overview
AXIS Q604 Series Hardware Overview 1 2 4 5 6 7 8 9 10 3 1 Unit holder (3x) 2 Camera base lid 3 Camera base lid screw T20 (3x) 4 Hook for safety wire 5 Part number (P/N) & Serial number (S/N) 6 Cable track (2x) 7 Foam gasket 8 Network connector (PoE+) 9 Multi-connector 10 Top cover 10
Page 13 - Network Connector
AXIS Q604 Series LED Indicators LED Color Indication Unlit Connection and normal operation Amber Steady during startup. Flashes during firmware upgrade. Amber/red Flashes amber/red if network connection is unavailableor lost. Red Flashes red for firmware upgrade failure. Status Green Shows steady gr...
Page 14 - I/O and Audio Connector; SD Card Slot; Unmount
AXIS Q604 Series NO NO NOTICE TICE TICE The product shall be connected using a shielded network cable (STP). All cables connectingthe product to the network shall be intended for their specific use. Make sure that thenetwork devices are installed in accordance with the manufacturer’s instructions. F...
Page 15 - Status
AXIS Q604 Series Multi-Connector Cable (sold separately) When connecting external equipment to the Axis product, a multi-connector cable (available fromAxis) is required in order to maintain the product’s IP rating. The multi-connector cable can bepurchased from your Axis reseller. Connect the multi...
Page 17 - Specifications; Operating Conditions; Power Consumption
AXIS Q604 Series I/O connector 1 2 3 4 5 6 DC power input AC power input Specifications Operating Conditions The Axis product is intended for indoor use. Product Classification Temperature Humidity AXIS Q6042AXIS Q6044AXIS Q6045 IEC 60721-4-3Class 3K3, 3M3IEC 60529 IP52 0 °C to 50 °C(32 °F to 122 °F...
Page 18 - Connectors; Install the Hardware; Replace the Dome Cover
AXIS Q604 Series Connectors SD Card Slot Supports SD cards with up to 64 GB of storage. For best recording performance, use an SDHCor SDXC card with speed class 10. Install the Hardware NO NO NOTICE TICE TICE • The AXIS product shall be connected using a shielded network cable (STP). All cables conn...
Page 19 - Install an SD Card; Hard Ceiling Mount
AXIS Q604 Series 2. Remove the dome bracket screws and remove the dome bracket and the dome cover from the dome ring. 3. Attach the dome bracket and the dome cover to the dome ring and tighten the screws (torque 1.2 Nm). 4. To install an SD card (not included), see Install an SD Card on page 19 . 5....
Page 20 - Drop Ceiling Mount
AXIS Q604 Series 5. Route and connect the network cable and the multi-connector cable (sold separately), if applicable, to the camera. NO NO NOTICE TICE TICE • Be careful not to damage the cables when connecting them. • Make sure that the foam gasket holes are aligned with the cable tracks and, if a...
Page 25 - Install the Midspan
AXIS Q604 Series 6. Turn the cable holders to keep the cables in place.7. Put the camera base lid back in its original position and tighten the screws (torque 1.5 Nm). 8. Slide the unit holders on the network camera into the slots in the mounting bracket and rotate the camera unit. 9. Secure the net...
Page 26 - Setup; Further Information
AXIS Q604 Series Access the Product Use the tools provided on the Installation and Management Software CD to assign an IP address,set the password and access the video stream. This information is also available from the supportpages on www.axis.com/techsup/ Reset to Factory Default Settings Importan...
Page 27 - Warranty Information
AXIS Q604 Series Warranty Information For information about Axis’ product warranty and thereto related information, see www.axis.com/warranty/ 27 E N G L IS H
Page 29 - USA; Errata; Valid for AXIS Q60 Series; About this document
Regulatory Information USA This equipment has been tested using an unshielded network cable (UTP) and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. This equipment has also been tested using a shielded network cable (STP) and found to comply with ...