Axis 35541 - Manuals - manualsarea.com

Page 2 - Electrical Specifications

Clear 25733, 25735 24 VAC 3.7 Amps 89 Watts Accessories: Heater: 50 Watts/Blower: 2 Watt Camera Power: Up to 37 Watts Tools Required: .100” Flat Head Screwdriver Phillips Head Screwdriver Note: 25735 includes no accessories 24 VAC 3.7 amperios 89 vatios Accesorios: Calentador: 50 Watts/Blower: 2 vat...

Page 3 - AXIS TECHNICAL SUPPORT

! ! SAFETY PRECAUTIONS IMPORTANT SAFEGUARDS1. Read Instructions - All the safety and operating instructions should be read before the unit is operated. 2. Retain Instructions - The safety and operating instructions should be retained for future reference. 3. Heed Warnings - All warnings on the unit ...

Page 4 - Wrap Teflon tape around the pipe threads; Screw the coupling onto the pipe threads

1 Securely mount bracket to wall. Pull wiring through bracket and position grommet as shown. • Con seguridad soporte del montaje a emparedar. Tire del cableado a través del soporte y del ojal de la posición según lo demostrado. • Solidement parenthèse de bâti à murer. Tirez le câblage par la parenth...

Page 5 - • Hacer las conexiones de cableado de la cúpula de la; Undo the lanyard, pull housing up and twist

5 Loop the lanyard over the set screw to temporarily hold housing. • Coloque el acollador sobre el tornillo de presión para celebrar temporalmente la cubierta. • Faites une boucle la lanière au-dessus de la vis de réglage pour tenir temporairement le logement. • Schlingen Sie die Abzuglinie über der...

Page 6 - BNC; These are recommended maximum distances

RJ45 BNC 24VAC 1 23 4 Camera Camera Heater/BlowerHeater/Blower Red Orange Yellow Green POWER 25 Watts 26 Watts 1/0 1 2 3 4 Alarm 1 Alarm 2 Alarm 3 Common Blue Violet Gray White Make the appropriate male and female connections. Indoor model does not include pre-run cables. • Haga las conexiones mascu...

Page 7 - Plate; Mounting; Captive; Captive

18 2685 Mounting Plate Mounting Hole Mounting Hole Mounting Hole Axis 214 (52 mm ) 2" Captive Screw (3) #8 x 3/8” Install the camera to the mounting plate using (3) 3mm x 12mm bolts and lock washers. Place (3) #8x3/8” screws on the spacers and line up the mounting slots. Slide plate in and secur...

Page 8 - camera into position.; zusammenzubauen. Sichern Sie Kamera in Position.; Loosen the screw to the right of the tab by; • Afloje el tornillo a la derecha de la lengüeta aproxi-; Align mounting plate and turn counter-

Attach camera to quick release plate as shown. Use spacers to assemble (4) 3” legs. Secure camera into position. • Una la cámara fotográfica a la placa rápida del lanzamiento según lo demostrado. Utilice los espaciadores para montar (4) las piernas del 3". Asegure la cámara fotográfica en la pos...

Page 10 - Camrea Specification; Camera Power Camera Power (at 24VAC REQUIRED); CAMERA POWER; POWER PLUG; For 12VDC unit connect power plug and; 4VAC units connect Red and Orange 24VAC

Camera specification for 24VAC outdoor housing. No electronics are included with indoor unit. • Especificación de la cámara fotográfica para la cubierta al aire libre 24VAC. No se incluye ninguna electrónica con la unidad de interior. • Spécifications d'appareil-photo pour le logement 24VAC extérieu...

Page 11 - Locking Screw

Remove power board. Use secrewdriver to release plastic fasteners by applying pressure to sides while pulling out. Construct mounting bracket assembly and attach camera. • Quitar poder bordo. Uso de liberar secrewdriver Sujetadores de plástico mediante la aplicación de presión a los lados Mientras t...

Page 12 - clockwise to lock in position.; Tab; Loop the lanyard around the tab inside the; Before; Align the arrows on the outside of the dome

17 Assemble Axis locking plate to quick release plate using (3) #8 bolts, washers and nuts. Connect the combined plates to the bracket and housing using (4) 1” and (4) ½” spacers and #8 bolts. Insert camera onto mounted locking plate and turn clockwise to lock in position. • Monte la placa de fijaci...

Page 13 - Fasten down the dome with a Phillips screwdriver.; • Limpie la bóveda limpia.

Fasten down the dome with a Phillips screwdriver. • Sujete abajo de la bóveda con un destornillador Phillips. • Attachez en bas du dôme avec un tournevis Phillips. • Befestigen Sie sich hinunter die Haube mit einem Kreuzkopfschraubenzieher. • Prenda abaixo a abóbada com uma chave de fenda Phillips. ...

Page 14 - Replacement Parts List; Part Number

25733 Replacement Parts List Part Number Description 1 RPFD7501 Lower Trim Ring (Long) 2a2b RCTFD7 Tinted Replacement Capsule RCFD7 Clear Replacement Capsule 3 RPFD703 Dome Clamping Bracket 4 RPFD072 24 Vac Heater 5 RPFD080 (12 Vdc) Blower (Used In 24v Housings) 6 RPFD060 Camera Bracket 7 RPRH707 Co...