Autostart CT-5000 - Manuals

CT-5000 Installation Guide P.5 WIRES at the IGNITION switch, this will compromise the OEM electrical system. E ORANGE (+) 30 A Accessories output This wire is for powering the heater blower motor. It is usually classed as an ACC. (no power in the CRANK position.) if it tests as an IGNITION (power in...

P.6 Installation Guide CT-5000 12-Pin Accessories Harness Wire Description 1 BLUE (–) AUX 3 (Trunk) output 500 mA negative output. This output can be used to control Trunk release (1-sec. pulse) or can be set to operate as a constant output as long as the TRUNK button is held pressed. (For Sunroof o...

CT-5000 Installation Guide P.7 10 WHITE (–) Ground out when running This is a 500-mA constant ground output that is active when the vehicle is running under a remote start. The output becomes active at the same time as the Ignition, and becomes inactive when the Module shuts down (i.e.: runtime has ...

P.8 Installation Guide CT-5000 12 YELLOW (+) Glow- plug Light input This positive input will monitor the Glow Plug Light in Diesel Mode: it will wait until the Glow Plug Light goes out to crank the Engine. Connect to the side of the Glow Plug Light that is positive when the Light is on. Note : In Di...

CT-5000 Installation Guide P.9 2-Pin Harness Wire Description 1 BLUE / WHITE ( -) AUX 2 output • 500 mA negative output. Can be programmed for one of the following options: • Constant while the LOCK and UNLOCK buttons are pressed, + 1 sec. after the buttons are released. • Pressing the LOCK + UNLOCK...

Remember: Once the Parking Lights are on Solid, you have up to 20 seconds to select a sub- menu. Failure to do so will result in the Module exiting the Programming Centre and you will have to Flash the Hood Pin once more. The Programming Assistance Button (A.k.a. PAB.) The PAB is located on the side...

CT-5000 Installation Guide P.11 The Parking Lights and the Siren will flash and chirp once, twice or 3 times to confirm entry into a Mode. 3. Release the Brake Pedal. Table 2 The Module can only be programmed Function by Function . After selecting a Mode (from 1 to 3), you will be taken to the first...

P.12 Installation Guide CT-5000 Car Finder disabled. O Constant output while PTION 3 pressed (press LOCK and UNLOCK ) Car Finder disabled. O Priority Door access o 2 nd PTION 4 n Unlock, and Car Finder enabled. • The Driver’s door unlocks upon the 1 st , 3 rd , 5 th … pressing of the UNLOCK button. ...

P.14 Installation Guide CT-5000 Table 5 Multi-S No manual adjustments are necessary. How hould go through the Tach programming procedure every time a new Unit is installed. peed Tach Programming ever, you s 1. FLASH the Hood Pin Switch . 2. Press and hold the Brake Pedal. • Press the LOCK and UNLOCK...

CT-5000 Installation Guide P.15 Away. A medium “tap” should trigger the Warn Away. A hard “tap” should trigger the Alarm. • All vehicles are different and therefore transmit shock level differently, if you are unable to set both zones to your satisfaction, referrer to p.12 ( Function 4 – Shock Sense...

Caution! Do not use more than one of the three sets of jumper pins simultaneously. The relay output rating on this Unit is 25A max output. Defective OEM solenoid switches can sometimes draw up to 50 or 60A, causing the 30A fuse to blow. Using a digital voltmeter, check the Starter wire for amperage ...

CT-5000 Installation Guide P.17 Safe Start (Child Safety Mode) ( OFF by default.) Requires the user presses the START/STOP button on the Transmitter twice within 3 seconds in order to start the vehicle. If the Special Safe Start Mode is selected (SWAP Start): • To start the vehicle, press the LOCK a...

P.18 Installation Guide CT-5000 Disarmed Notification This feature will notify the user when the vehicle is left disarmed after Ignition is turned off, or when the Module is disarmed after being previously armed, the opening or closing of a Door will cause the Horn or the Siren to sound once after 1...

CT-5000 Installation Guide P.19 • The Parking Lights and L.E.D. will flash the five events stored in memory. The first four playback codes are Start Failure Events , while the last playback code is an Intrusion Code . There is a pause after each event code is played back. The system will play back t...

CT-5000 Installation Guide P.21 made. This extra bit wire is wrapped around the exposed OEM wire to secure in place while you are soldering. − When all of the wires have been connected, solder the connections. When the solder has cooled, the connections are then individually taped up, to isolate the...

P.22 Installation Guide CT-5000 85 & 86: The Coil. These inputs energize the coil when one is +12 Volts, and the other is Negative. They are usually non-polarized, so it does not matter which one is positive (+) or negative (-). 87: Normally Open ( N/O). When the coil is energized, 87 is connect...

CT-5000 Installation Guide P.23 Problem: You need to power Multiple Ignition wires to remote start the vehicle, but your module only has one Ignition output available. Solution: You will need to add a second ignition relay to power the second ignition wire. (Jumping Ignition 1 to Ignition 2 is NEVER...

CT-5000 Installation Guide P.25 86 : Connects to a fused +12 Volt source. 87 : Connects to a Negative source. i.e. The spot where the remote start module is grounded. This becomes the supply for activating the vehicle's Trunk release wire. 87A : No connection. This terminal is not used in this appli...

P.28 Installation Guide CT-5000 28. I blow fuses every time I try the remote trunk release and I have already installed a relay. • Trunk release is reverse polarity, and not positive trigger. Chirps Chirps Description 1 • LOCK and ARM the system. • LOCK confirmation . • Entering Mode 1 in Programmin...

CT-5000 Installation Guide P.29 Diagnostics - Parking Lights Flash Rate Flashes Description 1 • Doors locked, Starter Kill armed. • End of Run Time. • TRUNK button pressed • START signal received by the Module. • Cold Weather Mode cancelled. • Cannot start after maximum number of attempts is reached...