Autostart AS-6205 SH - Manuals

AS-6205 SH Installation Guide P.5 6-Pin Main Ignition Harness Wire Description A RED +12 V Battery Connect to the largest 12 V supply wire at the Ignition harness. Ensure that the OEM power wire is fused for more than 30 A. NOTE: certain new vehicles have no suitable 12 volts source at the IGNITION ...

P.6 Installation Guide AS-6205 SH “under crank”. 3 GRAY (-) Hood Switch input Connect this wire to the Hood Pin-switch supplied. This input will disable or shut down the Remote Starter when the Hood is opened. It is also used for programming and therefore it is essential that it is installed. 4 ORAN...

P.8 Installation Guide AS-6205 SH 12 YELLOW(+) Glow- plug Light input This positive input will monitor the Glow Plug Light in Diesel Mode: it will wait until the Glow Plug Light goes out to crank the Engine. Connect to the side of the Glow Plug Light that is positive when the Light is on. Note : In ...

AS-6205 SH Installation Guide P.9 output ON for a 30-second cycle and shuts off automatically unless the user presses LOCK and UNLOCK before the end of that cycle, at which point, the AUX2 output shuts off. x This output can also be used as Priority Door Unlock. Car Finder is enabled or disabled in ...

The Programming Assistance Button(A.k.a. PAB.) The PAB is located on theside of the Module. Thispush button mimics theHood-Pin switch in order toavoid having to get out ofthe vehicle and pressing theHood-Pin switch. The PAB will work only when theHood is up. How to Program the Transmitter. 1. FLASH ...

AS-6205 SH Installation Guide P.11 The Module can only be programmed Function by Function . After selecting a Mode (from 1 to 3), you will be taken to the first Function of that Mode. After entering an Option number for Function 1, you will be automatically taken to Function 2, and so on; therefore,...

P.12 Installation Guide AS-6205 SH x All Doors unlock upon the 2 nd , 4 th , 6 th … pressing of the UNLOCK button. Mode 2 *indicates default setting Function 1 – Home Valet Mode OPTION 1 Home Valet enabled OPTION 2* Home Valet disabled OPTION 3 Home Valet disabled Function 2 – Safe Start OPTION 1 Sa...

AS-6205 SH Installation Guide P.13 OPTION 2* Ignition Valet - ENABLED OPTION 3 Ignition Valet - ENABLED Horn Honk / Siren Timing (Optional) 1. Make sure that Mode 3 Function 4 Option1 or Option 3 is activated. 2. FLASH the Hood Pin Switch Before the 20 seconds have passed, 3. Press and hold the Brak...

P.14 Installation Guide AS-6205 SH Table 5 Multi-Speed Tach Programming No manual adjustments are necessary. However, you should go through the Tach programming procedure every time a new Unit is installed. 1. FLASH the Hood Pin Switch . 2. Press and hold the Brake Pedal. x Press the LOCK and UNLOCK...

AS-6205 SH Installation Guide P.15 Away. A medium “tap” should trigger the Warn Away. A hard “tap” should trigger the Alarm. x All vehicles are different and therefore transmit shock level differently, if you are unable to set both zones to your satisfaction, referrer to p.12 ( Function 4 – Shock Se...

Caution! Do not use more than one of the threesets of jumper pins simultaneously.The relay output rating on this Unit is25A max output. Defective OEMsolenoid switches can sometimes draw up to 50 or 60A, causing the 30A fuseto blow. Using a digital voltmeter, checkthe Starter wire for amperage whenve...

AS-6205 SH Installation Guide P.17 Safe Start (Child Safety Mode) ( OFF by default.) Requires the user presses the START button on the Transmitter twice within 3 seconds in order to start the vehicle. If the Special Safe Start Mode is selected (SWAP Start): x To start the vehicle, press the LOCK and...

P.18 Installation Guide AS-6205 SH Disarmed Notification This feature will notify the user when the vehicle is left disarmed after Ignition is turned off, or when the Module is disarmed after being previously armed, the opening or closing of a Door will cause the Horn or the Siren to sound once afte...

AS-6205 SH Installation Guide P.19 10 x = Alarm condition Intrusion Codes 1 x = Power-up Reset: Battery disconnected / reconnected or dead… 2 x = Doors intrusion 3 x = Shock Sense 4 x = Hood 5 x = Panic 6 x = Ignition Note: “x” stands for one flash of the Parking Lights Intrusion Codes via LED light...

P.20 Installation Guide AS-6205 SH Diagnostics - Parking Lights Flash Rate Flashes Description 1 x Doors locked, Starter Kill armed. x End of Run Time. x TRUNK button pressed x START signal received by the Module. x Cold Weather Mode cancelled. x Cannot start after maximum number of attempts is reac...