Autostart AS-2775 - Manuals

Installation Guide P. 11 module's Trunk release output activates the relay. The ground signal is sent from 87 through 30 to the vehicle's Trunk release wire activating the switch and opening the trunk. Harness Description 6-pin Main Ignition Harness (a.k.a. The Primary harness) The two Red wires are...

P. 12 Installation Guide 5-pin Secondary Harness (a.k.a. the secondary harness) This harness has the remaining wires used in basic remote starter installations, positive parking light output, the safety shut down inputs, and the ground wire for the module. Wire Description 1 BLACK (–) Chassis ground...

P. 14 Installation Guide (Also known as the “wait-to-start light”.) The purpose of the Glow-plug circuit on diesel vehicles is to pre-heat the Combustion Chamber before the vehicle is started. When a Remote Starter is installed on a diesel vehicle, the Glow- plug section of the Ignition circuit must...

Installation Guide P. 15 compatibility and functionalities) . 5 Pager Port Is used to connect an optional AS-200P pager (to use this option, make sure to program pager option in Menu 3, Feature 5, Option 4 ). Entering Programming Mode This allows the installer to program the unit. Once the system is...

Installation Guide P. 17 2. Before the lights go out, press and hold the brake pedal and then press one of the following buttons: LOCK ...............................to access menu 1; UNLOCK ...........................to access menu 2; TRUNK …………………… to access menu 3; or START .........................

P. 18 Installation Guide OPTION 2* Ignition valet ENABLED MENU 3 * INDICATES DEFAULT SETTING FEATURE 1 – Home Valet OPTION 1 Home valet ENABLED OPTION 2* Home valet DISABLED FEATURE 2 – AUX 1 Programming OPTION 1 Horn confirmation upon the 2 nd press of the LOCK button. OPTION 2* Priority door acces...

Installation Guide P. 19 Multi-speed Tach Programming 1. Enter programming mode (see on page 15)  the parking lights will stay on for up to 20 seconds. 2. Before the lights go out, press and hold the brake pedal and press the LOCK and UNLOCK buttons simultaneously  the parking lights will flash 4 ...

P. 20 Installation Guide Clutch Bypass In order to remote start a manual transmission vehicle, the clutch switch must be bypassed. Clutch safety switch circuits can take many forms. Listed below are the most common ones. Some vehicles may also have a separate or combined switch on the clutch pedal f...

Installation Guide P. 21 modules connected to the G.O. Wire, a relay (and diodes) may have to be added to strengthen the negative current going to the clutch bypass. Positive: Very similar to the negative system, except that the vehicle's clutch relay is triggered by 12 volts instead of a negative s...

Installation Guide P. 23 Flashing LED To gain access to this feature, make sure the Flashing LED option has been enabled at the time of programming. Once this option is enabled, the user has the choice to toggle the Flashing LED ON and OFF at any given moment. To toggle between the Flashing LED ON a...

Installation Guide P. 25 If Safe Start is enabled, you can activate Cold Weather Mode by: • Pressing and releasing the START button, then; • Pressing and holding the START button until the parking lights flash 3 times . To verify whether the system is in Cold Weather Mode (automatic transmissions on...

P. 26 Installation Guide • To put the system o u t o f Valet mode using the TRANSMITTER (Remote Valet Mode): a. Press the UNLOCK and START buttons simultaneously until the parking lights flash twice. The LED on the antenna will flash quickly to indicate that the vehicle is now out of Valet mode. • T...

P. 28 Installation Guide To set the system to Ready Mode: If Ready Mode is enabled by remote If Ready Mode is enabled by handbrake 1. Ensure that all the doors, hood and trunk are closed. Make sure that the gear selector is in the neutral position. 2. With the engine already running, apply the parki...

Installation Guide P. 29 5. To save the new settings: press LOCK and UNLOCK . If 3 chirps are returned, the new settings have been saved Resetting the module to default features Resetting the module is not a required process. Most of the time, you can avoid resetting the module by fixing the issue d...

P. 30 Installation Guide ‰ Starter kill option. Sit inside the vehicle with all doors closed. Arm the vehicle, then try to start the engine with the key. The engine should not start. If the engine starts, rewire the starter kill to reach proper operation. ‰ Valet mode. Make sure the remote car start...

Installation Guide P. 31 Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, starter kill armed. • Run time has expired. • TRUNK button pressed. • Start signal received by the module. • Cold weather mode cancelled. 2 • Doors unlocked, starter kill disarmed. • Remote start a...

P. 32 Installation Guide Troubleshooting Q & A The following are some common installation-related issues. A problem or symptom is given and then possible solutions and/or suggestions as to areas to verify are enumerated. 1. I cannot program the remote control. • Do the parking lights come on whe...