Autostart AS-1820FM - Manuals

Be careful not to power up a Remote Car Starter before it is properly grounded. To avoid anyaccident, it is recommended to pull out the Fuses from their sockets before the installation, and toput them back during the very last steps. 6-pin Main Ignition Harness Wire Colour Function Description Conne...

P. 6 Installation Guide AS-1820 FM 5-Pin Secondary Harness Wire Colour Function Description 1 BLACK (–) Chassis ground input This wire must be connected to bare, unpainted metal (the Chassis or the true Body ground). It is preferable to use a factory ground bolt rather than a self-tapping screw. Scr...

AS-1820 FM Installation Guide P. 9 Flashing the Hood Pin Switch Flashing the Hood Pin switch is a procedure that brings the Remote Car Starter into Programming Mode. Once the Remote Car Starter is in Programming Mode, the installer will have up to 20 seconds to select one of the sub-menus. If the in...

The Programming Assistance Button (A.k.a. the PAB .) Mounted on the Remote Car Starter, this button can beused from within the vehicle instead ofthe Hood Pin switch in the Enginecompartment. This will spare the installerthe trouble of accessing the Hood Pinswitch in the Engine compartment. Caution T...

AS-1820 FM Installation Guide P. 11 2. Press and hold the Brake Pedal, – And press one of the following buttons on the Transmitter: • LOCK .................. to access Mode 1; • UNLOCK .............. to access Mode 2; • TRUNK ................ to access Mode 3. The Parking Lights will flash and the h...

AS-1820 FM Installation Guide P. 13 FUNCTION 3 – AUX 2 Programming OPTION 1 Constant output while the LOCK and UNLOCK buttons are pressed. In Safe Start Mode: activate AUX 2 by pressing the START button. OPTION 2* Toggle ON/OFF (with 30-second timeout) OPTION 2 Toggle ON/OFF (with 60-second timeout)...

P. 14 Installation Guide AS-1820 FM Note The L.E.D. follows the Parking Lights during the Transmitter Programming procedure. At any time, close the Hood to end the Tach-programming procedure. Automatic Tach Programming This simple procedure can replace the Multi-speed Tach Programming procedure: 1. ...

AS-1820 FM Installation Guide P. 15 Testing Before putting back the vehicle together, it is recommended to check that the system operates properly. The following testing procedures should be used to verify proper installation and operation of the system. Before testing, make sure that all connection...

Supplementary Information Fifth Relay Output (2 nd IGN, ACC or CRANK) Remote Car Starters of this series areequipped with an on-board high-currentprogrammable 5 th Relay that can be used to power a second Ignition, Accessory orCrank wire. The Unit uses 3 sets of pins; each setcorresponds to a specif...

once again). Please note that most OEM systems will not rearm the Alarm while the Engine is running, but will still lock the Doors. Smart Secure Lock If the vehicle is initially locked, upon remote START the Remote Car Starter will trigger an unlock pulse and a disarm pulse before the Engine is star...

P. 18 Installation Guide AS-1820 FM 1. Flash the Hood Pin switch (see Table 1) – Once inside Programming Mode, you have 13 seconds to complete the next step. 2. Press and release the Break Pedal 6 times (within 13 seconds from entering Programming Mode). 3. The Parking Lights will flash 8 times to c...

AS-1820 FM Installation Guide P. 19 Diagnostics – Chirps Table Chirps Description 1 • Doors locked, Starter Kill armed. • LOCK confirmation. • Entering Mode 1 in the Programming Centre. • Disarmed Notification 2 • Doors unlocked, Starter Kill disarmed. • Transmitter learnt. • Entering Remote Valet. ...

P. 20 Installation Guide AS-1820 FM Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, Starter Kill armed. • End of Run Time. • Run Time cancelled. • TRUNK button pressed • Start signal received by the Remote Car Starter. • Cold Weather Mode cancelled. • Cannot start after...