Autostart AS-1725 SH - Manuals

AS-1725 SH Installation Guide P. 5 This wire will power the Heater Blower Motor. Usually connected to the Accessories wire of the vehicle. The source wire must havepower with the Ignition Key in the IGNITION ON (RUN) position only ( no power in the CRANK position). E ORANGE (+) Accessories output (3...

P. 6 Installation Guide AS-1725 SH 12-Pin Accessories Harness Wire Colour Function Description 1 BLUE (–) Trunk / AUX 3 output 500 mA negative output. This output can be used to control theTrunk release (1-sec. pulse), or it can be set to operate as aconstant output as long as the TRUNK button is he...

AS-1725 SH Installation Guide P. 9 2-Pin Harness Wire Colour Function Description 1 BLUE/ WHITE (–) N/A This pin is not used. Leave it empty. 2 YELLOW (–) Parking Light output 500 mA negative Parking Light output Note: Ensure that the voltage does not vary when the dimmer control switch is turned up...

Remember: Once the Parking Lights are ON (solid), you have up to 20 seconds to select a sub-menu. If you do notselect a sub-menu within 20 seconds, the RemoteCar Starter will exit Programming Mode and you willhave to flash the Hood Pin switch once again. The Programming Assistance Button (A.k.a. the...

AS-1725 SH Installation Guide P. 11 To program a Transmitter on the second vehicle for Multi-car Operation, you must press the TRUNK and LOCK buttons simultaneously (instead of LOCK or UNLOCK ) in step 2 of the Transmitter code-learning procedure: Entering Programming Options Mode The Remote Car Sta...

P. 12 Installation Guide AS-1725 SH Programming Options MODE 1 * INDICATES DEFAULT SETTING FUNCTION 1 – Ignition-controlled Door Locks OPTION 1* Ignition Lock DISABLED OPTION 2 Ignition Lock ENABLED OPTION 3 Ignition UNLOCK ONLY OPTION 4 Ignition LOCK ONLY FUNCTION 2 – Secure Lock OPTION 1* Secure L...

AS-1725 SH Installation Guide P. 13 OPTION 2* Ignition Valet ENABLED OPTION 3 Ignition Valet ENABLED MODE 3 * INDICATES DEFAULT SETTING FUNCTION 1 – Home Valet TM OPTION 1 Home Valet ENABLED OPTION 2* Home Valet DISABLED OPTION 3 Home Valet DISABLED FUNCTION 2 – AUX 3 / Zone 3 Programming OPTION 1 1...

P. 14 Installation Guide AS-1725 SH of certain Ignition systems are sometimes too low or too high for the Remote Car Starter, causing failed start-ups at various temperatures. 1. Flash the Hood Pin switch (see Table 1) – The Parking Lights will stay ON for up to 20 seconds. – Before the lights go ou...

AS-1725 SH Installation Guide P. 15 a. To increase the Horn pulse by 3 ms, press the LOCK button. b. To decrease the pulse by 3 ms, press the UNLOCK button. c. To increase the pulse by 10 ms, press the START or STOP button. d. To decrease the pulse by 10 ms, press the TRUNK button. 5. To save the ne...

Closing Up Use tie-wraps or screws to properly secure the Remote Car Starter and keep the wiringaway from any moving parts such as the Parking Brakes or Steering Column Shafts. Mount all switches in good and accessible locations where they do not risk getting kicked orhit accidentally. Most comeback...

P. 18 Installation Guide AS-1725 SH x Active Arming : the Starter Kill will not arm automatically. Press the LOCK button to arm and the UNLOCK button to disarm it. x Passive Arming: the Starter Kill will arm automatically if it is not armed by remote within a 60-sec. delay. Press UNLOCK to disarm. x...

AS-1725 SH Installation Guide P. 19 Start Failure Codes through the Parking Lights 1 x = No Start 3 x = Hardware Reset4 x = Brakes 5 x = No Tach Cut-off 6 x = Hood 7 x = Engine Running, no Ignition detected, or Tach before Start Note : “ x ” stands for one flash of the Parking Lights Diagnostics – P...

P. 20 Installation Guide AS-1725 SH Constant flashes up to 30 sec. x Panic Mode is triggered.