Audiovox VOD122 - Manuals - manualsarea.com

Page 2 - Select the color that matches the interior trim.

An LCD panel and / or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation.If the LCD panel or video monitor is used for television reception, video or DVD...

Page 3 - MATERIALS INCLUDED IN THIS PACKAGE:; Hardware Package; Optional Accessories

1 TOOLS REQUIRED: #2 Phillips Screwdriver#1 Phillips ScrewdriverUtility or Razor Knife or ShearsWire StrippersUpholstery hook tool (for removal of panels as necessary)Electrical TapeMasking TapeMultimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe)Marker pen – to ma...

Page 4 - Installing The Snap On Covers; Place the pod on a soft surface to avoid damaging the plastic.; Housing; Installing The Shroud

2 Installing The Snap On Covers Begin by hooking area “A” (above) over the dome light and slide the cover over the pod. The cover will snap in place. Place the pod on a soft surface to avoid damaging the plastic. Open the screen and hook the two tabs “B” on the bottom edge of the screen. Snap the op...

Page 5 - Removing The Snap On Cover (Shroud) From The Housing; pry tool; Removing The Snap On Cover (Screen Back) From LCD The Housing

3 1 2 3 6 5 7 4 Work on a soft surface to avoid damaging the plastic.Insert the supplied pry tool between the Housing and Snap On Cover (Shroud) , then press the pry tool to release the Snap On Cover (Shroud) . Removing The Snap On Cover (Shroud) From The Housing Insert the supplied pry tool between...

Page 6 - VEHICLE PREPARATION:; installation of the VOD122 and related console accessories.; GENERAL INSTALLATION APPROACH:; respective locations.

4 VEHICLE PREPARATION: 1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is off), and also a good ground generally, these wires can be found at the ignition switch or fuse-box. 2) The mounting method and location will vary from vehicle to vehicle, s...

Page 7 - GENERAL SYSTEM CONFIGURATIONS:; OSD will appear on the screen for 4~5 seconds; SOURCE; and; FMM; buttons on the unit

5 GENERAL SYSTEM CONFIGURATIONS: The following is intended to provide some of the system configurations that are possible with the VOD122Drop Down Video Systems: The VOD122 has an option that allows the user to select from two IR transmit and receive codes (M1 or M2). This feature can be used when u...

Page 8 - TRIM RING INSTALLATION:; trim ring to video monitor.

6 TRIM RING INSTALLATION: Note: This page only covers special installation considerations for thick trim ring installation. If the video monitor is to be installed in a vehicle with the thick trim ring, it may need to be trimmed to fit the contour of the vehicle Headliner. Note: The trim rings suppl...

Page 9 - MOUNTING THE TRIM RING

7 MOUNTING THE TRIM RING Roof Roof Support Headliner Mounting Bracket Self-drilling Screws Trim Ring Video Unit M5 Screw

Page 11 - Figure A; Auxillary Video Display; PODTVT2

9 VOD122 Figure A ANT.IN RF OUT OUT FUSE DC IN Red RCA (Audio Right) Clean the IR Receiver Window on the front of the VCP. Remove Adhesive Backing and Apply IR LED to IR Yellow RCA (Video) White RCA (Audio Left) "Y" Adapter for use withNon-StereoInstallationsItem# 5 Power Connector 4 Pin Acc...

Page 12 - CONNECTING THE DOME LIGHTS; Positive Switched Dome Lighting; Factory Dome light circuit

10 CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched syste...

Page 13 - Negative Switched Dome Lighting; No power at Video Monitor

11 Negative Switched Dome Lighting Red / black - Lamp on To 12 pin connector To constant To constant Black / red - Lamp commonPurple / brown - Lamp Auto Factory Door ajarswitch or BodyControl computer Troubleshooting: SYMPTOM: REMEDY: No power at Video Monitor Verify +12 VDC on Red wire at 2 pin Pow...