Audiovox PRO9776C - Manuals

Page 5 - This Remote Start/Alarm System is designed to be used with; Automatic Transmission; as it is not waterproof.; This switch must be installed in all applications.; Mount the switch in a location away

128-8787 5 of 24 5 This Remote Start/Alarm System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plug pre-heat which may be required for certain diesel vehicles, (see selectab...

Page 6 - only! Although this combination; IT MUST NOT; be installed

128-8787 6 of 24 6 SHOCK SENSOR: Select a centrally located, solid mounting surface for the shock sensor that will allow consistent operationfrom all areas of the vehicle. The selected location must be within 18" of the control module to allow routingand connecting of the 4 pin harness. Secure t...

Page 7 - YELLOW START WIRE DETAIL; Ignition 1 Output

128-8787 7 of 24 7 Failure to make this connection properly can result in personal injury and property damage. In all installationsit is the responsibility of the installing technician to test the remote start unit and assure that the vehiclecannot start via RF control in any gear selection other th...

Page 9 - WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness; Parking Light Flasher Feed; Parking Light Wiring Detail

128-8787 9 of 24 9 WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness White w/ Red Trace Wire: Parking Light Flasher Feed This wire is the common contact of the on board parking light flasher relay. If the vehicle you are workingon has +12 volt switched parking lights, connect this wire to...

Page 11 - General Motors VATS By-Pass Diagram; Ignition 3 Output

128-8787 11 of 24 11 General Motors VATS By-Pass Diagram Light Blue Wire: Ignition 3 Output This wire provides a 300 mA ground output that becomes active 3 seconds before the Remote Start Unitinitializes, and remains grounded while running plus an additional 4 seconds after the Remote Start Unitturn...

Page 12 - Entry Illumination Ground Output; Entry Illumination Detail; Negative Inhibit Input; Gray w/ Black Trace Negative Inhibit Safety Shut Down Detail

128-8787 12 of 24 12 Green w/ White trace Wire: Entry Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm thealarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered. Thiswire should b...

Page 13 - Brake Switch Positive Shutdown Detail

128-8787 13 of 24 13 Orange Wire: Ground When Armed Output This wire provides a 300 mA ground output when the alarm circuit is armed to control the starter inhibitrelay. Connect the Orange wire to terminal #86 (orange wire) of the relay provided. Connect terminal #85(red wire) of the relay to an ign...

Page 14 - Chassis Ground Source; Chassis Ground Connection Detail; Tachometer Input Signal; Tachometer Input Wiring Detail; Diesel Wait To Start Input

128-8787 14 of 24 14 Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Becertain to remove any paint or grease and secure this wire with a self taping screw and ring terminal. Chassis Ground Connection Detail Gree...

Page 15 - Negative Door Switch Wiring Detail; Delayed 300 mA Pulsed Channel 3 Output; Channel 3 Relay Wiring Detail; 00 mA Latched Channel 4 Output

128-8787 15 of 24 15 Negative Door Switch Wiring Detail Dark Blue Wire: Delayed 300 mA Pulsed Channel 3 Output The Dark Blue wire supplies a 300 mA ground pulsed output whenever channel three of the receiver is accessed.Pressing the pre-programmed transmitter button for three seconds will access cha...

Page 17 - Wire Ground Switched Door Lock/Unlock Wiring Detail; Wire Positive Switched Door Locks:

128-8787 17 of 24 17 2 Pin Transponder Control Output: (Yellow Connector) This output is intended to allow the control of a transponder bypass interface module or transponderbypass relay. The system also allows software selections to control the way in which this output operates,see remote start fea...

Page 18 - Wire Positive Switched Door Lock/Unlock Wiring Detail; In this application, the

128-8787 18 of 24 18 3 Wire Positive Switched Door Lock/Unlock Wiring Detail 3 Wire Ground Switched 2 Step Door Locks In this application, the red wire provides a ground pulse during arming, or the pulsed ground lock output. Connect the red wire to the wire that provides a low current ground signal ...

Page 22 - Method 1; also effect other warning tones such as the light on reminder.

128-8787 22 of 24 22 vehicle. The information concerning the Mechanical Neutral Safety Switch provided below will help you to determine if the vehicle you are working on has this type of safety switch and will provide alternate wiring methods to accommodate this situation. MECHANICAL NEUTRAL SAFETY ...

Page 23 - METHOD 2; Pin Upgrade Data Bus/Flash Logic Module:

128-8787 23 of 24 23 METHOD 2 To connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch...