Audiovox PRO9776C - Manual
Audiovox PRO9776C – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 5 – This Remote Start/Alarm System is designed to be used with; Automatic Transmission; as it is not waterproof.; This switch must be installed in all applications.; Mount the switch in a location away
- Page 6 – only! Although this combination; IT MUST NOT; be installed
- Page 7 – YELLOW START WIRE DETAIL; Ignition 1 Output
- Page 9 – WIRING CONNECTIONS: Multi Pin Accessory Input/Output Harness; Parking Light Flasher Feed; Parking Light Wiring Detail
- Page 11 – General Motors VATS By-Pass Diagram; Ignition 3 Output
- Page 12 – Entry Illumination Ground Output; Entry Illumination Detail; Negative Inhibit Input; Gray w/ Black Trace Negative Inhibit Safety Shut Down Detail
- Page 13 – Brake Switch Positive Shutdown Detail
- Page 14 – Chassis Ground Source; Chassis Ground Connection Detail; Tachometer Input Signal; Tachometer Input Wiring Detail; Diesel Wait To Start Input
- Page 15 – Negative Door Switch Wiring Detail; Delayed 300 mA Pulsed Channel 3 Output; Channel 3 Relay Wiring Detail; 00 mA Latched Channel 4 Output
- Page 17 – Wire Ground Switched Door Lock/Unlock Wiring Detail; Wire Positive Switched Door Locks:
- Page 18 – Wire Positive Switched Door Lock/Unlock Wiring Detail; In this application, the
- Page 22 – Method 1; also effect other warning tones such as the light on reminder.
- Page 23 – METHOD 2; Pin Upgrade Data Bus/Flash Logic Module:
128-8787
1 of 24
1
SELECT
ABLE FEA
TURES
The select
able features can be set manually as explained below
, or with the RF feature programmer
.
T
o
set features using the RF programmer
, follow the instructions p
ackaged with the programmer
.
Factory default settings are indicated by bold text.
Note :
The method of manual override can either be selected to operate from the valet switch or operate as custom code.
Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.
Note:
Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.
Also, No data will be indicated if a feature is not available for a particular model. The unit will enter the feature but no s
election will be available.
RF Programmable Feature Bank 1 Is For T
ransmitter Programming See T
ransmitter Programming Guide.
RF Programmable Features Bank 2 Is Alarm Selectable Features:
Feature Selection
1 Chirp
2 Chirps
3 Chirps
4 Chirps
5 Chirps
6 Chirps
1st DoorL/UL
1 Sec.
3.5
Sec.
1 Sec L, Dbl. U/L
Dbl L, 1 Sec UL
Dbl
L,
Dbl
UL
1
S
l/350mS
ul
2nd
Accy
Lock
Auto Lock On
Auto Lock Off
3rd
Accy
. UL
Auto
UL
Dr
.
Auto
UL
A
ll
Auto UL Off
4th Headlights
Not
A
vailable
5th Passive
Locks
Passive
Active
6th Pass/Act
Arm
Passive Arm
Active Arm
7th Siren/Horn
Siren/Horn
Siren Only
Horn
Only
8th Horn Chirp
10mS
16mS
30mS
40mS
50mS
9th O/R Method
Custom
Code
V
alet
10th 2 S
tep U/L
O
n
Off
1
1th Chp Del
Tx
O
n
Off
12th V
olt
s/HdW
ire
Not A
vailable
13th Trigger Circuits
All On
Doors Off
Hood & Trunk
Off
All Off
14th L/UL Poll
Not A
vailable
15th
Aux Channel 5 Select
Pulsed
Push & Hold
10
Seconds
20
Seconds
Latch On/Off
Hold 3.5 Sec For O/P
16th
Aux Channel 6 Select
Pulsed
Push & Hold
10
Seconds
20
Seconds
Latch On/Off
Hold 3.5 Sec For O/P
17th
Aux Channel 7 Select
Pulsed
Push & Hold
10
Seconds
20
Seconds
Latch On/Off
Hold 3.5 Sec For O/P
18th Trigger Delay
Not
A
vailable
When using the RF programmer
, enter the program mode as follows:
Turn the ignition on.
Press and release valet switch 3 times.
Turn ignition off then on.
Press and hold valet switch for 5 seconds.
Siren chirps 2 times indicating access to RF feature program mode.
Model PRO9776C
Installation Manual
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
128-8787 5 of 24 5 This Remote Start/Alarm System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plug pre-heat which may be required for certain diesel vehicles, (see selectab...
128-8787 6 of 24 6 SHOCK SENSOR: Select a centrally located, solid mounting surface for the shock sensor that will allow consistent operationfrom all areas of the vehicle. The selected location must be within 18" of the control module to allow routingand connecting of the 4 pin harness. Secure t...
128-8787 7 of 24 7 Failure to make this connection properly can result in personal injury and property damage. In all installationsit is the responsibility of the installing technician to test the remote start unit and assure that the vehiclecannot start via RF control in any gear selection other th...
