Audiovox AXT-1200 - Manuals

Page 2 - INDEX

INDEX Specifications.....................................................................3Precautions........................................................................ 4Installation Instructions...................................................... 5Wiring Instructions............................

Page 3 - HIGH PERFORMANCE STEREO AMPLIFIER; Saturday

Input Impedance: Low-level 10K OhmsHigh-level 100 Ohms Input Sensitivity: Low-level 200 mV - 8 V.High-level 2V - 10 V. Filter type: Selectable High/Full/Low-pass Crossover @ 12 dB/Octave Filter Crossover: LPF 50-250 Hz (variable) HPF 50-250 Hz (variable)Supply Voltage: 12 volts, negative ground Fuse...

Page 4 - must; PRECAUTIONS

1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired correctly. Please follow the wiring instructions carefully for the type of system being used. 2. The last lead to be connected is the wire to the positive( ) terminal of ...

Page 5 - CHECK BEFORE YOU DRILL!; Secure the amplifier to the mounting surface using; INSTALLATION INSTRUCTIONS

1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling.Inadequate air circulation will cause the temperatureof the amplifier to rise and will trigger the thermalprotection mode. 2. Place the amplifier on the mounting surface and mark the locations of th...

Page 6 - WIRING INSTRUCTIONS

The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, ormixed-mono application. The following pages illustrate the input and output wiring for these types. please refer to theappropriate diagrams for the system configuration you are usin...

Page 7 - Speaker Connections; ground any speaker leads to the chassis of the vehicle.; DO NOT; use both input levels at the same time.

4. Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #16 gauge wire should be used for the speaker leads but in no case thinner than #18 gauge. For leads in excess...

Page 8 - INPUT WIRING DIAGRAM; WIRE SIDE VIEW

-8- USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUT, NOT BOTH. IMPORTANT RCA TYPE SHIELED CABLES (NOT INCLUDED) Right LOW-LEVEL RCA OUTPUTS CAR STEREO INPUT WIRING DIAGRAM W h it e G re en B la ck B ro w n G ra y Left CHASSIS GROUND ON RADIO LOW-LEVEL RCA OUTPUTS NOTE: When using High-Level (Speaker) Outpu...

Page 9 - BATTERY; OUTPUT WIRING DIAGRAM

-9- CAR STEREO GROUND BATTERY FOR 12 VOLT USE ONLY AUTO-ANTENNA LEAD GROUND METALSECTION OF VEHICLE EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRTOR GREASE FROM AREA FOR GOOD CONNECTION. RIGHT SPEAKER 2-8 OHM LEFT SPEAKER 2-8 OHM OUTPUT WIRING DIAGRAM LEFT RIGHT REM BATT GND FUSE FUSE BRIDGED BRIDGE...

Page 10 - OPERATION; Power Indicator Lamps

-10- 3 1 2 5 OPERATION 4 6 HI-INPUT HI-INPUT GND GND L + L + R + R + LL RR RR LL PWR PWR PRT PRT MIN MIN MAX MAX GAIN GAIN 0dB 0dB 18dB 18dB 50Hz 50Hz 250Hz 250Hz LPF LPF 50Hz 50Hz 250Hz 250Hz HPF HPF X-OVER X-OVER HPF HPF LPF LPF FULL FULL BASS BOOST BASS BOOST LEFT RIGHT REM REM BATT BATT GND GND ...

Page 11 - below; LPF Crossover Frequency Control

-11- High Level Input Connection If the car stereo not does not provide low-level outputs, the amplifier may be connected via the speaker (high-level) outputs from the stereo. Wire the speaker leads from the car stereo to the 5-pin adaptor harness as shown in the diagram (shielded cable is not requi...

Page 12 - Fuse

9 -12- Fuse The circuitry of the amplifier is protected from damage byan automotive-type fast-blow fuse. If fuse replacementis necessary, use only fuses of the of the same ampere rating as originally supplied with the unit. The use of fuseswith incorrect ratings may cause serious damage to theamplif...

Page 13 - CANADA; 0 DAY/12MONTH LIMITED WARRANTY

AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof,under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, suchdefect(s) will be repaired ...

Page 14 - Printed in Korea

2003 Audiovox Electronics Corporation, Hauppauge, N.Y. C C Printed in Korea 128-6565