Audiovox AS9233ST - Manuals

Page 5 - This Remote Start/Alarm System is designed to be used with; Automatic Transmission Vehicles Only!; Mount the switch in the hood

128-8605 5 of 20 5 This Remote Start/Alarm System is designed to be used with Automatic Transmission Vehicles Only! The unit provides a selectable ignition control that allows a number of selectable timed outputs for glow plugpre-heat which may be required for certain diesel vehicles, (see selectabl...

Page 6 - only! Although this combination; IT MUST NOT; be installed

128-8605 6 of 20 6 from all areas of the vehicle. The selected location must be within 18" of the control module to allow routingand connecting of the 4 pin harness. Secure the shock sensor to the chosen location using two #8 self tapingsheet metal screws. The sensor can also be secured to an ex...

Page 7 - SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.; YELLOW START WIRE DETAIL; Ignition 1 Output

128-8605 7 of 20 7 Note: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electricalneutral switch configuration, this connection must be made between the starter inhibit relay, (whenused) and the neutral safety switch as shown in the following diagram. F...

Page 8 - Parking Light Flasher Feed; Parking Light Wiring Detail; Siren Output; Optional Siren Wiring Detail

128-8605 8 of 20 8 Purple Wire: (+) Door Trigger Input If the vehicle's door courtesy light switches + 12 volts when the door is opened, (Some Fords and someImports), you must connect this wire to the positive output from one of the vehicle's door pin switches. Inmost cases, the Purple wire will nee...

Page 9 - Hood Pin Switch Detail

128-8605 9 of 20 9 Dark Green Wire: (-) Instant Trigger Input This is the instant on ground trigger input wire. This wire must be connected to the hood and trunk pin switches where installed. Note: This wire will be shunted when remote control channel 3 is accessed, (trunk release). This wire will r...

Page 10 - Negative Inhibit Input; Grey Negative Inhibit Safety Shut Down Detail; Ground When Armed Output; Starter Inhibit Wiring Detail

128-8605 10 of 20 10 Black White/Black Grey Wire: Negative Inhibit Input The Grey w/ Black Trace wire provides an instant shutdown for the Remote Start Control Module whenever it is grounded. Connect the Grey trace wire to the hood pin switch previously installed. This wire must be routed through a ...

Page 11 - Chassis Ground Source; Chassis Ground Connection Detail; Positive Inhibit Input; Brake Switch Positive Shutdown Detail; Tachometer Input Signal; Tachometer Input Wiring Detail

128-8605 11 of 20 11 Black Wire: Chassis Ground Source Connect the Black wire to a known vehicle ground source or to a solid clean metal part of the chassis. Becertain to remove any paint or grease and secure this wire with a self taping screw and ring terminal. Chassis Ground Connection Detail Brow...

Page 12 - Negative Door Switch Wiring Detail

128-8605 12 of 20 12 Green/Yellow Wire: Diesel Wait To Start Input The Green/Yellow wire will connect to a diesel vehicles glow plug wire. When the unit receives a start command,this wire must go to + 12 then to ground to allow the crank sequence to begin. When ignition #1 is activated by theremote ...

Page 14 - Pin Transponder Control Output:; see remote start feature # 10 for setting this output.; Wire Ground Switched Door Lock Circuits:

128-8605 14 of 20 14 output would be to disarm a factory theft deterrent system to prevent false triggering of the factory alarm when the remote start unit engages or when the 785 is used to unlock the doors. Black w/ Light Green Trace Wire: Pulsed Ground Output After Start The Black w/ Light Green ...

Page 15 - Wire Positive Switched Door Locks:; TIMED START OPERATION:

128-8605 15 of 20 15 3 Wire Positive Switched Door Locks: In this application, the Red wire of the door lock harness provides a + 12 volt pulse during the disarming sequence,or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from the factory doorunlock switc...

Page 18 - before considering either alternative.; METHOD 1; To connect to the key in sensor as shown in method 1:

128-8605 18 of 20 18 MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing a remote start device. Often when the ignition switch is turned off while the gear selector is in a...

Page 19 - METHOD 2; To connect to the key in sensor circuit as shown for method 2:; Pin Upgrade Data Bus/Flash Logic Module:

128-8605 19 of 20 19 METHOD 2 To connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch...