Audiovox AS 9075a - Manuals

Page 3 - SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.

128-6602 3 of 16 Remote Start Connection WIRING THE 6 PIN MAIN POWER HARNESS:RED w/ WHITE Trace Wire: + 12 volts Battery 1 SourceConnect this wire to a + 12 VDC constant source found at the vehicle's ignition switch using the 30 Amp fuseand holder provided. This wire provides power for the control c...

Page 4 - WIRING CONNECTIONS: 12 Pin Input / Output Harness; BLACK w/WHITE Tracer Wire: Control Switch; WIRING THE 6-PIN MAIN POWER HARNESS

128-6602 4 of 16 BLUE Wire: Ignition 1 OutputConnect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignitionkey is turned to the to the "ON" or "RUN" and the "START" or CRANK" positions, and will have 0 volts whenthe key ...

Page 5 - Brake Switch Positive Shutdown Detail; PRESENTLY CONNECTED TO IN THE VEHICLE.

128-6602 5 of 16 the Black w/ White wire is at open circuit through the control switch, the remote starter is disabled.Connect the Black w/ White tracer wire to one of the wires from the back of the previously mounted control switch.Connect the remaining wire of the control switch to chassis ground....

Page 6 - LIGHT BLUE Wire: Ignition 3 / Shock Disable Output; key's value from the resistor pack supplied.

128-6602 6 of 16 This wire should be connected to the ignition input of the alarm system.The Yellow w/ Black wire output will allow you to remote start the vehicle while leaving the alarm armed, and to lock/unlock the doors while running under control of the remote start unit. (2) WHITE Wires: Parki...

Page 7 - General Motors VATS By-Pass Diagram; DARK GREEN/ORANGE Wire: Tach Sensor Input

128-6602 7 of 16 NOTE: These wires are typically White w/ Black trace and Violet w/ Yellow trace, however in later model Cadillacs, they are run through an orange sleeve, and are either both Black, both Yellow, or bothWhite wires. Consult the factory service manual for additional information. 3. Con...

Page 8 - Tachometer Input Wiring Detail

128-6602 8 of 16 8 Tachometer Input Wiring Detail WIRING THE 4 PIN AUXILIARY OUTPUT HARNESSThe auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during differentstages of the Remote Start unit's operation. Understanding these outputs and the time in w...

Page 10 - TIMED START OPERATION:

128-6602 10 of 16 This Remote Car Starter will learn the tach rate of most vehicles single ignition coils, multiple coil packs, and or singleinjector. To learn tach; 1. Start with the ignition switch in the "OFF" position and the programming switch in the "ON" position. 2. Turn the i...

Page 12 - the ignition switch off. DO NOT attempt to remove the key.

128-6602 12 of 16 1 2 TESTING YOUR INSTALLATION:CAUTION!! The following procedure must be performed after the installation of an Audiovox Remote Start Device. It is the responsibility of the installing technician to complete these tests. Failure totest the unit in the following manner may result in ...

Page 14 - METHOD 1; To connect to the key in sensor as shown in method 1:

128-6602 14 of 16 margin of safety and will prevent the vehicle with a Mechanical Neutral Start Switch from starting in gear.WE ADVISES THAT YOU MAINTAIN THE FACTORY CIRCUIT WHENEVER POSSIBLE. The followingtwo circuits may be used only if the above circuit is not available.NOTE: When completing an i...

Page 15 - COMPLETING THE INSTALLATION:; METHOD 2

128-6602 15 of 16 To connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground. C. Locate the key in sensor switch wire that c...