Audiovox AS-9055T - Manuals

Page 2 - MUST HAVE a Tach Signal; INSTALLATION OF THE MAJOR COMPONENTS:; PROGRAM SWITCH; AUTOMATIC TRANSMISSIONS; only! Although this combination Keyless; IT MUST NOT; be installed into a

128-7184 2 of 16 This Remote Start System is designed for use with Automatic Transmission Vehicles Only! The unit provides waitto start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, thenthe unit will remain in the Gasoline mode setting, w...

Page 4 - SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.; Ignition 1 Output

128-7184 4 of 16 NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutralswitch configuration, this connection must be made between the starter inhibit relay, (when used) and theneutral safety switch as shown in the following diagram. Fai...

Page 5 - Accessory Output; WIRING CONNECTIONS: 12 Pin Input / Output Harness; Chassis Ground Source; Control Switch; Negative Inhibit Input 1

128-7184 5 of 16 VIOLET WIRE: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignitionswitch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to the...

Page 6 - Positive Inhibit Input 2; Brake Switch Positive Shutdown Detail; Switch

128-7184 6 of 16 BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2 Any time + 12 Volts is applied to the Brown w/ Black tracer wire, the Remote Starter will stop operating, even if the signalis received from the transmitter. If the brake light switch in the vehicle switches + 12 Volts to the brak...

Page 7 - Ignition 3 / Shock Disable Output; from the resistor pack supplied.; General Motors VATS By-Pass Diagram

128-7184 7 of 16 LIGHT BLUE Wire: Ignition 3 / Shock Disable Output This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes,and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of theappl...

Page 8 - Tach Sensor Input; Tachometer Input Wiring Detail; Diesel Wait To Start Input; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS; Pulsed Ground Output Before Start

128-7184 8 of 16 DARK GREEN Wire: Tach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. Thiswire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect tothe negative s...

Page 9 - Pin Blue Connector :; EXAMPLE; using the ignition key; is stored and the unit is now out of the program mode.

128-7184 9 of 16 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement is more than 300 mA. 2 Pin Blue Connector : Push-Button Programming Switch Route the gray and black wires in the 2 pin connector from the previously installed push-button progr...

Page 11 - switch off. DO NOT attempt to remove the key.

128-7184 11 of 16 11 W A R N I N G ! ! DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE OPERATION OF THE HOOD PIN SAFETY SHUT DOWN FEATURE. MANUAL SHUT DOWN / ENABLE CIRCUIT: The intent of the manual shut down / enable circuit is to allow the vehicle operator to prevent operation of...

Page 12 - KEY IN SENSOR CIRCUITS:; Method 1

128-7184 12 of 16 configuration prevents mechanical operation while the vehicle is in gear but offers no consideration for electrical operation.Because of this potential problem, this installation requires the additional connection of a safety wire from the remote start device tothe vehicle Park/Neu...

Page 13 - METHOD 1; METHOD 2

128-7184 13 of 16 METHOD 1 To connect to the key in sensor as shown in method 1:A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.B. Cut this wire and connect the ignition cylinder side to chassis ground.C. Locate the key in sensor switch wire that conn...

Page 14 - COMPLETING THE INSTALLATION:; under the dash board or in the engine compartment areas.; point these out to the customer.

128-7184 14 of 16 14 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. Ifthis is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must beconnected to the Gray/Black wire of the Remote Start Unit. ...