Audiovox AS-9055T - Manual

Audiovox AS-9055T

Audiovox AS-9055T – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
Page: / 16

Table of Contents:

  • Page 2 – MUST HAVE a Tach Signal; INSTALLATION OF THE MAJOR COMPONENTS:; PROGRAM SWITCH; AUTOMATIC TRANSMISSIONS; only! Although this combination Keyless; IT MUST NOT; be installed into a
  • Page 4 – SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.; Ignition 1 Output
  • Page 5 – Accessory Output; WIRING CONNECTIONS: 12 Pin Input / Output Harness; Chassis Ground Source; Control Switch; Negative Inhibit Input 1
  • Page 6 – Positive Inhibit Input 2; Brake Switch Positive Shutdown Detail; Switch
  • Page 7 – Ignition 3 / Shock Disable Output; from the resistor pack supplied.; General Motors VATS By-Pass Diagram
  • Page 8 – Tach Sensor Input; Tachometer Input Wiring Detail; Diesel Wait To Start Input; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS; Pulsed Ground Output Before Start
  • Page 9 – Pin Blue Connector :; EXAMPLE; using the ignition key; is stored and the unit is now out of the program mode.
  • Page 11 – switch off. DO NOT attempt to remove the key.
  • Page 12 – KEY IN SENSOR CIRCUITS:; Method 1
  • Page 13 – METHOD 1; METHOD 2
  • Page 14 – COMPLETING THE INSTALLATION:; under the dash board or in the engine compartment areas.; point these out to the customer.
Loading the manual

128-7184

1 of 16

Kit Contents

(1) - Control Module

(2) - 1 Button High Frequency Transmitters

(1) - 1 Channel Code Learning Receiver

(1) - Multi Pin Input/Output Harness

(1) - Six Pin Power Harness

(1) - Four Pin Accessory Output

(Pulse Before & After Start, During Crank & After Shut Down)

(2) - 30 Amp In-line Fuse Holders With Fuses

(1) - Control Switch

(1) - Push-Button Programming Switch

(1) - Ring Terminal

(4) - 1/2" Long Screws

(1) - Pin Switch

(1) - Remote Start Warning Label

(1) - Literature Package

Model AS-9055T

Installation Manual

Released: 6-28-04

Remote Start System

Installation Instructions

This Unit Is Intended For Installation In Vehicles With

12 Volt Negative Ground Electrical Systems,

Gasoline or Diesel With True Tach Reference

And Automatic Transmissions Only.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - MUST HAVE a Tach Signal; INSTALLATION OF THE MAJOR COMPONENTS:; PROGRAM SWITCH; AUTOMATIC TRANSMISSIONS; only! Although this combination Keyless; IT MUST NOT; be installed into a

128-7184 2 of 16 This Remote Start System is designed for use with Automatic Transmission Vehicles Only! The unit provides waitto start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, thenthe unit will remain in the Gasoline mode setting, w...

Page 4 - SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.; Ignition 1 Output

128-7184 4 of 16 NOTE: This wire must be connected to the vehicle side of the starter cut relay (when used). For the electrical neutralswitch configuration, this connection must be made between the starter inhibit relay, (when used) and theneutral safety switch as shown in the following diagram. Fai...

Page 5 - Accessory Output; WIRING CONNECTIONS: 12 Pin Input / Output Harness; Chassis Ground Source; Control Switch; Negative Inhibit Input 1

128-7184 5 of 16 VIOLET WIRE: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignitionswitch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to the...

Other Audiovox Models