Audiovox AS-9055 - Manuals - manualsarea.com

Page 2 - INSTALLATION OF THE MAJOR COMPONENTS:; PROGRAM SWITCH

128-6832 2 of 16 This Remote Start System is designed for use with Automatic Transmission Vehicles Only! The unit provides waitto start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, thenthe unit will remain in the Gasoline mode setting, w...

Page 3 - Starter Output

128-6832 3 of 16 3 THE RECEIVER/ANTENNA ASSEMBLY: The Superheterodyne Receiver Antenna Assembly provided with this unit allows routing from below the dashboardfor maximum operating range. Choose a location above the belt line (dashboard) of the vehicle for best reception.Special considerations must ...

Page 5 - Accessory Output; WIRING CONNECTIONS: 12 Pin Input / Output Harness; Black Wire: Chassis Ground Source; Control Switch; GRAY WIRE: Negative Inhibit Input 1

128-6832 5 of 16 VIOLET WIRE: Accessory Output Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignitionswitch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to the...

Page 6 - BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2; Brake Switch Positive Shutdown Detail; Switch

128-6832 6 of 16 BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2 Any time + 12 Volts is applied to the Brown w/ Black tracer wire, the Remote Starter will stop operating, even if the signalis received from the transmitter. If the brake light switch in the vehicle switches + 12 Volts to the brak...

Page 7 - LIGHT BLUE Wire: Ignition 3 / Shock Disable Output; General Motors VATS By-Pass Diagram

128-6832 7 of 16 LIGHT BLUE Wire: Ignition 3 / Shock Disable Output This wire provides a 300mA ground output that becomes active 3 seconds before the Remote Start Unit initializes,and remains grounded while running plus an additional 4 seconds after the Remote Start Unit turns off. In all of theappl...

Page 8 - DARK GREEN Wire: Tach Sensor Input; Tachometer Input Wiring Detail; Green/Yellow Wire: Diesel Wait To Start Input

128-6832 8 of 16 DARK GREEN Wire: Tach Sensor Input This wire will continually monitor the engine tach rate while the unit is under power of the Remote Start module. Thiswire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect tothe negative s...

Page 9 - To program these selectable features:; All applications require that tach be programmed.

128-6832 9 of 16 NOTE: The outputs above are low current outputs and must be used with a relay if the circuit's requirement ismore than 300 mA.2 Pin Blue Connector : Programming Switch Route the gray and black wires in the 2 pin connector from the previously installed programming switch to the contr...

Page 10 - HOOD PIN SAFETY SHUT DOWN:

128-6832 10 of 16 10 X Pause,etc...X Pause,etc... 3. Diagnostics:1. Be sure that programmable feature number #6 is set to the "Diagnostics On" mode.2. Press and hold the program switch on, then turn the ignition key to the "ON" position.3. The lights will flash and the number of flas...

Page 12 - KEY IN SENSOR CIRCUITS:

128-6832 12 of 16 configuration prevents mechanical operation while the vehicle is in gear but offers no consideration for electrical operation.Because of this potential problem, this installation requires the additional connection of a safety wire from the remote start device tothe vehicle Park/Neu...

Page 13 - METHOD 1; METHOD 2

128-6832 13 of 16 METHOD 1 To connect to the key in sensor as shown in method 1:A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.B. Cut this wire and connect the ignition cylinder side to chassis ground.C. Locate the key in sensor switch wire that conn...

Page 14 - COMPLETING THE INSTALLATION:; point these out to the customer.

128-6832 14 of 16 14 NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must beconnected to the Gray/Black wire of the Remote Start Unit....