Audiovox APS 685 - Manuals - manualsarea.com

Page 6 - Brake Switch Positive Shutdown Detail; WIRE THAT IT IS PRESENTLY CONNECTED TO IN THE VEHICLE.

BROWN w/ BLACK Tracer Wire: Positive Inhibit Input 2Any time + 12 Volts is applied to the Brown w/ Black tracer wire, the Remote Starter will stop operating, evenif the signal is received from the transmitter. If the brake light switch in the vehicle switches + 12 Volts to thebrake light circuit, co...

Page 8 - General Motors VATS By-Pass Diagram

General Motors VATS By-Pass Diagram DARK GREEN/ORANGE Wire: Tach Sensor InputThis wire will continually monitor the engine tach rate while the unit is under power of the Remote Startmodule. This wire will be routed to the vehicle ECM tach input or through the firewall into the enginecompartment and ...

Page 9 - Wire Ground Switched Door Lock/Unlock Wiring Detail

3 Wire Ground Switched 2 Step Door LocksIn this application, the red wire provides a ground pulse during locking, or the pulsed ground lock output.Connect the red wire to the wire that provides a low current ground signal from the factory door lock switchto the factory door lock control relay.The gr...

Page 11 - Wire Positive Switched Door Lock/Unlock Wiring Detail

3 Wire Positive Switched Door Locks:In this application, the Red wire of the door lock harness provides a + 12 volt pulse during the unlockingsequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire fromthe factory door unlock switch to the factory door ...

Page 12 - Blue and Green w/Black Trace Wires - 2 Pin Accessory Output Harness; some remote start trigger inputs, will damage the control module.; Channel 3 Relay Wiring Detail

Black w/ Yellow Trace Wire: Ground Output During Start (Crank)The Black w/ Yellow Trace wire will provide a 300 mA ground output while the starter output of the remotestart unit is active. This output can be used to activate the Crank Low/Bulb Test wire found in some GMvehicles. This wire is also re...

Page 13 - Entry Illumination Detail; certain to connect the tach input wire.

Dark Blue/Black and Green/White - 2 Pin Input/Output Harness: Dark Blue/Black Trace Wire: External Trigger InputThe Dark Blue/Black trace wire allows the remote start unit to be activated from an external source. Theintent of this wire is to allow the unit to be controlled from a "POSSE/CAR-LINK...

Page 15 - change, the above sequence will have to be followed.

TIMED START PROGRAM:The Remote Start unit has the ability to start the vehicle automatically at timed intervals. This feature isuseful in extremely cold climates where starting the engine is the only means to keep the battery chargedand fluids warm. The operator has the option to have the unit start...

Page 16 - the ignition switch off. DO NOT attempt to remove the key.

1. With the driver's window in the down position, start the vehicle using the RF transmitter.2. Reach inside the car and pull the hood release.3. Raise the hood and confirm that the remote start unit shuts down.If the unit fails this test, recheck your pin switch connection to the Gray/Black wire of...

Page 18 - METHOD 1

KEY IN SENSOR CIRCUITS:If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there aretwo alternatives available. Although not preferred, the vehicle Key In Sensor may be reconfigured to allowa margin of safety and will prevent the vehicle with a Mechanical Neu...

Page 19 - mote Start Unit as shown below.; METHOD 2; sure to clean the surface before affixing the label.

mote Start Unit as shown below. METHOD 2 To connect to the key in sensor circuit as shown for method 2:A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.B. Cut this wire and connect the ignition cylinder side to chassis ground.C. Locate the key in senso...

Page 20 - WIRING DIAGRAM