Audiovox 128-8115 - Manuals

Page 2 - To program these selectable features

128-8115 2 of 19 Page 2 To program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Select...

Page 5 - INSTALLATION OF THE MAJOR COMPONENTS:; PUSHBUTTON LED SWITCH; This system is to be used in vehicles with; AUTOMATIC TRANSMISSIONS; only! Although this combination Keyless; IT MUST NOT; be installed into a

128-8115 5 of 19 Page 5 This Remote Start System is designed for use with Automatic Transmission Vehicles Only! The unit provideswait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is notconnected, then the unit will remain in the Gasoline mode set...

Page 6 - WIRING THE 6 PIN MAIN POWER HARNESS:; Do not remove the fuse holders from this wire harness. Fuses must be; Trace Wire: + 12 volts Battery 1 Source; Starter Output

128-8115 6 of 19 Page 6 I M P O R T A N T ! DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS INTO THECONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE. AFTER SELECTINGYOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE BATTERY CABLE FROM THE...

Page 7 - SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.; Ignition 1 Output

128-8115 7 of 19 Page 7 SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS. BLUE WIRE: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition keyis turned to the to the "ON" or "RUN" and the "START" ...

Page 8 - WIRING CONNECTIONS: 12 Pin Input / Output Harness; Chassis Ground Source

128-8115 8 of 19 Page 8 Connect this wire to the Accessory wire from the ignition switch. This wire will show + 12 volts when the ignitionswitch is turned to the "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turnedto the "OFF" and "...

Page 9 - Brake Switch Positive Shutdown Detail; Ignition 3 / Shock Disable Output

128-8115 9 of 19 Page 9 Brake Switch Positive Shutdown Detail YELLOW w/ BLACK Tracer Wire: + 12 Volt Alarm By - Pass Output NOTE: You must disconnect the ignition input of the alarm from any other wire that it is presently connected to in the vehicle.This wire provides a + 12 Volt output when the ig...

Page 10 - General Motors VATS By-Pass Diagram; Tach Sensor Input

128-8115 10 of 19 Page 10 the applications described below, a relay will be required. The Light Blue wire can be used to accommodate thefollowing situations: A. Shock Sensor By Pass: If there is Shock Sensor used with an alarm system and it is not shunted during the Remote Start activationperiod, th...

Page 11 - Tachometer Input Wiring Detail; Diesel Wait To Start Input; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS; Pulsed Ground Output Before Start; Push-Button LED Programming Switch Assembly:

128-8115 11 of 19 Page 11 cases will operate properly from one multi coil pack regardless of the number of cylinders. If the vehicle has asingle coil unit for each cylinder, it may be necessary to connect this wire to more than one cylinder for proper tachreference. See multi coil wiring detail show...

Page 13 - cylinder, four coil systems, connect to any of the three coils.

128-8115 13 of 19 Page 13 columns. The Green/Black wires should be connected to the negative (-) terminal of the respective cylindernumber which appears in any of the circles. 2. For vehicles utilizing 2 cylinder firing per coil pack, connect Green/Black to the tach side of each coil pack. For 8 cyl...

Page 14 - switch off. DO NOT attempt to remove the key.; REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARILY; KEY IN SENSOR CIRCUITS:

128-8115 14 of 19 Page 14 To test the integrity of the Neutral Start Safety Circuit:1. Set the vehicle parking brake.2. Block the drive wheels to prevent vehicle movement.3. Temporarily disconnect the Brown/Black positive shut down wire from the vehicle's brake switch.4. Sitting in the vehicle, star...

Page 15 - METHOD 1

128-8115 15 of 19 Page 15 prevent the vehicle with a Mechanical Neutral Start Switch from starting in gear.AUDIOVOX ADVISES THAT YOU MAINTAIN THE FACTORY CIRCUIT WHENEVER POSSIBLE. The following twocircuits may be used only if the above circuit is not available. NOTE: When completing an installation...

Page 16 - METHOD 2; Pin Upgrade Data Bus/Flash Logic Module:

128-8115 16 of 19 Page 16 METHOD 2 To connect to the key in sensor circuit as shown for method 2:A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch.B. Cut this wire and connect the ignition cylinder side to chassis ground.C. Locate the key in sensor swit...

Page 17 - COMPLETING THE INSTALLATION:; clean the surface before affixing the label.

128-8115 17 of 19 Page 17 COMPLETING THE INSTALLATION: After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of thesystem:1. If you have not done so already, place the red rubber handle cover over the handle of the control switch for ease of iden...

Page 18 - THIS PAGE LEFT BLANK INTENTIONALLY

128-8115 18 of 19 Page 18 THIS PAGE LEFT BLANK INTENTIONALLY