Audiovox 128-8115 - Manual

Audiovox 128-8115

Audiovox 128-8115 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
Page: / 20

Table of Contents:

  • Page 2 – To program these selectable features
  • Page 5 – INSTALLATION OF THE MAJOR COMPONENTS:; PUSHBUTTON LED SWITCH; This system is to be used in vehicles with; AUTOMATIC TRANSMISSIONS; only! Although this combination Keyless; IT MUST NOT; be installed into a
  • Page 6 – WIRING THE 6 PIN MAIN POWER HARNESS:; Do not remove the fuse holders from this wire harness. Fuses must be; Trace Wire: + 12 volts Battery 1 Source; Starter Output
  • Page 7 – SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.; Ignition 1 Output
  • Page 8 – WIRING CONNECTIONS: 12 Pin Input / Output Harness; Chassis Ground Source
  • Page 9 – Brake Switch Positive Shutdown Detail; Ignition 3 / Shock Disable Output
  • Page 10 – General Motors VATS By-Pass Diagram; Tach Sensor Input
  • Page 11 – Tachometer Input Wiring Detail; Diesel Wait To Start Input; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS; Pulsed Ground Output Before Start; Push-Button LED Programming Switch Assembly:
  • Page 13 – cylinder, four coil systems, connect to any of the three coils.
  • Page 14 – switch off. DO NOT attempt to remove the key.; REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARILY; KEY IN SENSOR CIRCUITS:
  • Page 15 – METHOD 1
  • Page 16 – METHOD 2; Pin Upgrade Data Bus/Flash Logic Module:
  • Page 17 – COMPLETING THE INSTALLATION:; clean the surface before affixing the label.
  • Page 18 – THIS PAGE LEFT BLANK INTENTIONALLY
Loading the manual

128-8115

1 of 19

Page 1

The select

able features can be set manually as explained below

, or with the RF feature programmer

.

T

o

set features using the RF programmer

, follow the instructions p

ackaged with the programmer

.

Factory default settings are indicated by bold text.

Note :

The method of manual override can either be selected to operate from the valet switch or operate as custom code.

Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.

NOTE: Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.

Also, No data will be indicated if a feature is not available for a particular model. The unit will enter the feature but no s

election will be available.

RF Programmable Feature Bank 1 Is For T

ransmitter Programming See T

ransmitter Programming Guide.

RF Programmable Features Bank 2 Is Alarm Selectable Features:

Feature Selection

1 Chirp

2 Chirps

3 Chirps

4 Chirps

5 Chirps

6 Chirps

1st DoorL/UL

1 Sec.

3.5

Sec.

1 Sec L, Dbl. U/L

Dbl L, 1 Sec UL

Dbl

L,

Dbl

UL

1

S

l/350mS

ul

2nd

Accy Lock

Not Available

3rd

Accy

. UL

Not Available

4th Headlights

Not Available

5th Passive Locks

Not Available

6th Pass/Act

Arm

Not Available

7th Siren/Horn

Not Available

8th Horn Chirp

Not Available

9th O/R Method

Not Available

10th 2 S

tep U/L

Not Available

1

1th Chp Del

Tx

Not Available

12th V

olt

age/Hd W

ire

Not Available

13th Trigger Circuits

Not Available

14th Lock/Unlock Poll

Not Available

15th

Aux Ch 5 Sel

Not Available

16th

Aux Ch 6 Sel

Not Available

17th

Aux Ch 7 Sel

Not Available

18th Trigger Delay

Not Available

When using the RF programmer

, enter the program mode as follows:

Turn the ignition on

Press and release valet switch 3 times

turn ignition off then on

Press and hold valet switch for 5 seconds

Siren and or lights chirp/flash 2 times indicating access to RF feature program mode.

Model APS-921

Installation Manual

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - To program these selectable features

128-8115 2 of 19 Page 2 To program these selectable features; Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Then On Short chirp, then long chirp This Action Accesses Feature Bank 2 Alarm Select...

Page 5 - INSTALLATION OF THE MAJOR COMPONENTS:; PUSHBUTTON LED SWITCH; This system is to be used in vehicles with; AUTOMATIC TRANSMISSIONS; only! Although this combination Keyless; IT MUST NOT; be installed into a

128-8115 5 of 19 Page 5 This Remote Start System is designed for use with Automatic Transmission Vehicles Only! The unit provideswait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is notconnected, then the unit will remain in the Gasoline mode set...

Page 6 - WIRING THE 6 PIN MAIN POWER HARNESS:; Do not remove the fuse holders from this wire harness. Fuses must be; Trace Wire: + 12 volts Battery 1 Source; Starter Output

128-8115 6 of 19 Page 6 I M P O R T A N T ! DO NOT PLUG THE SIX PIN MAIN POWER HARNESS OR THE MULTI PIN INPUT / OUTPUT HARNESS INTO THECONTROL MODULE UNTIL ALL CONNECTIONS TO THE VEHICLE HAVE BEEN MADE. AFTER SELECTINGYOUR TARGET WIRES AS DEFINED BELOW, DISCONNECT THE NEGATIVE BATTERY CABLE FROM THE...

Other Audiovox Models