Page 2 - only! Although this Remote; IT MUST NOT; be installed into a vehicle
128-7760 2 of 16 2 This Remote Start/Keyless Entry Upgrade System is designed to be used with Automatic TransmissionVehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glow plugpreheat which may be required for certain diesel vehicles, (see selectable fe...
Page 3 - WIRING THE 6 PIN MAIN POWER HARNESS:; Do not remove the fuse holders from this wire harness. Fuses must be; + 12 volt Battery 1 Source; Starter Output
128-7760 3 of 16 3 WIRING THE 6 PIN MAIN POWER HARNESS: Note: Do not remove the fuse holders from this wire harness. Fuses must be used and located as close as possible to the power source for adequate protec- tion of the vehicle. Fused RED w/ WHITE TRACE WIRE: + 12 volt Battery 1 Source Locate the ...
Page 4 - WIRING CONNECTIONS: 12 Pin Input / Output Harness; Chassis Ground Source; BLACK w/WHITE Tracer Wire: Control Switch
128-7760 4 of 16 4 SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS. BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignitionkey is turned to the to the "ON" or "RUN" and the "START" or CR...
Page 5 - Brake Switch Positive Shutdown Detail; PRESENTLY CONNECTED TO IN THE VEHICLE.
128-7760 5 of 16 5 the Black w/ White wire is at open circuit through the control switch, the remote starter is disabled.Connect the Black w/ White tracer wire to one of the wires from the back of the previously mounted control switch.Connect the remaining wire of the control switch to chassis groun...
Page 6 - LIGHT BLUE Wire: Ignition 3 / Shock Disable Output; key's value from the resistor pack supplied.
128-7760 6 of 16 6 This wire should be connected to the ignition input of the alarm system.The Yellow w/ Black wire output will allow you to remote start the vehicle while leaving the alarm armed, and to lock/unlock the doors while running under control of the remote start unit. (2) WHITE Wires: Par...
Page 7 - terminal #85 of the relay to a fused + 12 volt battery source.; General Motors VATS By-Pass Diagram; DARK GREEN/ORANGE Wire: Tach Sensor Input
128-7760 7 of 16 7 NOTE: These wires are typically White w/ Black trace and Violet w/ Yellow trace, however in later modelCadillacs, they are run through an orange sleeve, and are either both Black, both Yellow, or bothWhite wires. Consult the factory service manual for additional information. 3. Co...
Page 8 - Tachometer Input Wiring Detail; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS; Trigger Input
128-7760 8 of 16 8 Tachometer Input Wiring Detail WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during differentstages of the Remote Start unit's operation. Understanding these outputs and the time in ...
Page 13 - KEY IN SENSOR CIRCUITS:
128-7760 13 of 16 13 this vehicle. The information concerning the Mechanical Neutral Safety Switch provided below will helpyou to determine if the vehicle you are working on has this type of safety switch and will provide alternatewiring methods to accommodate this situation. CAUTION! REMEMBER TO RE...
Page 14 - circuits may be used only if the above circuit is not available.; Method 1; To connect to the key in sensor as shown in method 1:
128-7760 14 of 16 14 circuits may be used only if the above circuit is not available. NOTE: When completing an installation using either of the following key in sensor circuits, if the operator inserts the ignition key while the vehicle is running under the control of the Remote Start, the vehiclewi...
Page 15 - COMPLETING THE INSTALLATION:; from the program switch.; METHOD 2
128-7760 15 of 16 15 C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder . D. Cut this wire and connect the ignition cylinder side to the Remote Start Negative Safety Shut down Wire Gray/Black, using a 4002 series diode as shown above. NOTE: A second 4002 ...