Audiovox 128-7760 - Manual

Audiovox 128-7760

Audiovox 128-7760 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
Page: / 16

Table of Contents:

  • Page 2 – only! Although this Remote; IT MUST NOT; be installed into a vehicle
  • Page 3 – WIRING THE 6 PIN MAIN POWER HARNESS:; Do not remove the fuse holders from this wire harness. Fuses must be; + 12 volt Battery 1 Source; Starter Output
  • Page 4 – WIRING CONNECTIONS: 12 Pin Input / Output Harness; Chassis Ground Source; BLACK w/WHITE Tracer Wire: Control Switch
  • Page 5 – Brake Switch Positive Shutdown Detail; PRESENTLY CONNECTED TO IN THE VEHICLE.
  • Page 6 – LIGHT BLUE Wire: Ignition 3 / Shock Disable Output; key's value from the resistor pack supplied.
  • Page 7 – terminal #85 of the relay to a fused + 12 volt battery source.; General Motors VATS By-Pass Diagram; DARK GREEN/ORANGE Wire: Tach Sensor Input
  • Page 8 – Tachometer Input Wiring Detail; WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS; Trigger Input
  • Page 13 – KEY IN SENSOR CIRCUITS:
  • Page 14 – circuits may be used only if the above circuit is not available.; Method 1; To connect to the key in sensor as shown in method 1:
  • Page 15 – COMPLETING THE INSTALLATION:; from the program switch.; METHOD 2
Loading the manual

128-7760

1 of 16

1

Model AS 9076

Installation Manual

Remote Start Upgrade Module

Installation Instructions

This Unit Is Intended For Installation In Vehicles With

12 Volt Negative Ground Electrical Systems,

Gasoline or Diesel With True Tach Reference

And Automatic Transmissions Only.

Kit Contents

(1) -Control Module
(1) - Multi Pin Input/Output Harness
(1) - Six Pin Power Harness
(1) - Four Pin Auxiliary Harness
(1) - Four Pin I/O Harness
(1) - Control Switch / Programming Switch
(1) - Ring Terminal
(4) - 1/2" Long Screws
(1) - Pin Switch
(1) - Remote Start Warning Label
(1) - Literature Package

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - only! Although this Remote; IT MUST NOT; be installed into a vehicle

128-7760 2 of 16 2 This Remote Start/Keyless Entry Upgrade System is designed to be used with Automatic TransmissionVehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glow plugpreheat which may be required for certain diesel vehicles, (see selectable fe...

Page 3 - WIRING THE 6 PIN MAIN POWER HARNESS:; Do not remove the fuse holders from this wire harness. Fuses must be; + 12 volt Battery 1 Source; Starter Output

128-7760 3 of 16 3 WIRING THE 6 PIN MAIN POWER HARNESS: Note: Do not remove the fuse holders from this wire harness. Fuses must be used and located as close as possible to the power source for adequate protec- tion of the vehicle. Fused RED w/ WHITE TRACE WIRE: + 12 volt Battery 1 Source Locate the ...

Page 4 - WIRING CONNECTIONS: 12 Pin Input / Output Harness; Chassis Ground Source; BLACK w/WHITE Tracer Wire: Control Switch

128-7760 4 of 16 4 SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS. BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignitionkey is turned to the to the "ON" or "RUN" and the "START" or CR...

Other Audiovox Models