AT&T MG9150J - Manuals - manualsarea.com

Page 2 - Centralized Telephone Programming Quick Reference; TO ENTER PROGRAMMING MODE; System Features; TO ERASE A FEATURE OR AUTO; Refer to document number MG9150J.

Centralized Telephone Programming Quick Reference Place the Programming Overlay on the dial pad of the system display phone at extension 10 or 11 (Extension 11 programming: P+ > = R3.0, PII > R1.0) TO ENTER PROGRAMMING MODE PRESS [ Feature ] [ 0 ] [ 0 ] PRESS [ System Program ] [ System Progra...

Page 3 - System Features Continued

System Features Continued GROUP CALLING—RING/PAGEP+ 1 Grp < R2.0, 4 Grp > R3.0 (p. 5-64)PII 4 Grp > R1.0 (p. 5-96) P+ > R4.0PII > R3.0 (p. 5-97) (p. 5-132) For ringing the group: PRESS a programmable button PRESS left [ Intercom ] [ 7 ] DIAL a Calling Group number (1-4) For paging the...

Page 4 - System Programming Quick Reference; System

System Programming Quick Reference Place the Programming Overlay on the dial pad of the system display phone at extension 10 or 11P+ > R 3.0, PII > R1.0 TO START SYSTEM PROGRAMMING TO END SYSTEM PROGRAMMING TO CYCLE THROUGH SYSTEM TO CYCLE THROUGH AVAILABLE PRESS [ Feature ] [ 0 ] [ 0 ] PRESS ...

Page 5 - Lines

Lines DIAL MODE P+ > R1.0 (p. 5-36) PII > R1.0 (p. 5-58) DIAL #201DIAL a line number (01–12 P+,01– 24 PII) DIAL 1 = Touch-Tone ✔ 2 = Rotary PRESS [ Next Item ] to program another line HOLD DISCONNECT TIME PII > R3.0 (p. 5-94) P+ > R1.0 (p. 5-74) PII > R1.0 (p. 5-106) DIAL #203 DIAL a ...

Page 6 - Extensions

System Programming Quick Reference Place the Programming Overlay on the dial pad of the system display phone at extension 10 or 11 TO START SYSTEM PROGRAMMING TO END SYSTEM PROGRAMMING TO CYCLE THROUGH SYSTEM TO CYCLE THROUGH AVAILABLE PRESS [ Feature ] [ 0 ] [ 0 ] PRESS [ Feature ] [ 0 ] [ 0 ] PROG...

Page 7 - Dialing Restrictions and Permissions; System Speed Dial Numbers

SYSTEM RESET – PROGRAMMING SAVED P+ > R1.0PII > R1.0 (p. 5-138)(p. 5-181) IMPORTANT: Using this procedure disconnects any active calls but retains system settings. Use it only if the system fails to function correctly after a power failure or down period.DIAL #728 Dialing Restrictions and Perm...

Page 8 - Groups

System Programming Quick Reference Place the Programming Overlay on the dial pad of the system display phone at extension 10 or 11 TO START SYSTEM PROGRAMMING TO END SYSTEM PROGRAMMING TO CYCLE THROUGH SYSTEM TO CYCLE THROUGH AVAILABLE PRESS [ Feature ] [ 0 ] [ 0 ] PRESS [ Feature ] [ 0 ] [ 0 ] PROG...

Page 9 - Programming Mixed Telephone Types; Overview; Find the location of the button in the picture of the target phone.

Programming Mixed Telephone Types A Overview This appendix provides information about programming from a PARTNER-34D phone toMLS-model phones and from an MLS-34D phone to PARTNER-model phones. In thesesituations, you should be aware that the button that you press at extension 10 or 11 (theprogrammin...

Page 10 - Figure 1. Programming from a PARTNER-34D Phone

PARTNER-34D Overlay MLS-6 Phone MLS-18D/12D/12 Phone PARTNER-18D Overlay MLS-34D Phone Figure 1. Programming from a PARTNER-34D Phone 10

Page 11 - Figure 2. Programming from a MLS-34D Phone

MLS-34D Overlay PARTNER-6 Phone PARTNER-18D/18 Phone PARTNER-34D Phone MLS-18D/MLS-12D Overlay Figure 2. Programming from a MLS-34D Phone 11

Page 12 - System Identifier; SYSTEM; PARTNER II release 3 would return 3 beeps, a 1.5; Notes

System Identifier The System Identifier feature allows a PARTNER, PARTNER PLUS or PARTNER II system to identify its release numberto NSAC personnel. While speaking with the customer, ask them to dial [ Feature ] [ # ] [ 1 ]. The beeps heard immediately after entering this code is used to identify th...