AT&T 5635 - Manuals - manualsarea.com

Page 3 - announcement has not been recorded.; Charge the handset batteries for 10 hours.; Record an announcement.; Telephone Operation; Making Calls

sleeve toward the screw head. Insert the screws into the holes you started. Tighten the screws until thesmall end of the mounting sleeve is flat against the wall. 11. Connect the telephone line cord. The telephone line cord has a snap in plug on each end. Insert one of the plugs into the jack in the...

Page 4 - If You Go Out of Range:

Occasionally, especially when you pick up the handset between rings, you may not be connected. If thishappens, press PHONE on the handset to connect the call.If the handset rings when it’s out of the base, pick up the handset, extend the antenna and press PHONE toanswer the call. Hanging up: To end ...

Page 6 - Memory Dialing; Programming a Number Into Memory

Using the Intercom During a Phone Call First place the call on hold by pressing HOLD. Then use the intercom. While you are using the intercom, the Phone Lights on the handset and the base will blink to show that your call has not been disconnected.The person on the other end of the phone call will n...

Page 7 - REDIAL; Programming and Dialing Long Numbers or Sequences; MEM; Changing or Replacing a Stored Number

To use the directory card concealed in the back of your handset, press the arrow and slide the door towardthe top of the handset until it snaps in place. The directory card has an erasable surface. If you write inpencil, you’ll find it easy to change names when necessary. NOTE: If the door slips off...

Page 8 - Answering System Operation: At The Base; About Mailboxes

Answering System Operation: At The Base About Mailboxes This answering system provides two voice mailboxes. These mailboxes provide a convenient way to sharean answering system with other members of your household or business. Callers using a touch tone phone can choose the mailbox in which their me...

Page 9 - Setting System to Answer Calls

Pre-recorded Announcement If you do not record your own announcement, callers will hear this announcement: “Hello. Please leave amessage after the tone.” The Message Window blinks to indicate that the user needs to record an announcement. To select the pre-recorded announcement as your announcement ...

Page 10 - Message Window

While the system is taking a call, the Message Window displays “-.” After a message is recorded, thedisplay changes to show the total number of recorded messages. NOTE: Messages are limited to a maximum of two minutes each. If the caller is still speaking aftertwo minutes, is silent for more than 7 ...

Page 13 - Screening Incoming Calls; ANNC; Priority Calling; To use Priority Calling,; Answering System Operation: Away from the Base; ANS SYS

Screening Incoming Calls To screen calls, adjust SPEAKER VOLUME so that you can hear the caller’s voice.If you decide to take a call, either use the cordless handset or lift the handset of any telephone on the sameline to talk to the caller. NOTE: If the announcement does not stop right away, press ...

Page 14 - enter your access; (it is not necessary to wait for the announcement to finish.); Reviewing Your Access Code

If it doesn’t receive any instructions in a few seconds, the system will automatically play all of yourmessages for you. First Mailbox 1 followed by Mailbox 2. You can allow the system to play yourmessages, or you can use the number buttons on the handset to direct the system to perform any of the o...

Page 16 - The Outgoing Announcement; Reviewing Your Outgoing Announcement; Recording a Memo

You can work with the clock setting any time after the system has given you the two-beep signal to indicatethat it is ready to accept a command. Reviewing the Day/Time Setting Press and release 8 (CLOCK). The answering system will announce the current day/time setting and then beep twice to indicate...

Page 17 - Recording a Telephone Conversation; Call Monitoring; OFF; Call Intercept; PHONE; Room Monitor

3. Speak into the phone in a normal tone of voice. Just as with messages, the system will accept memosup to two minutes in length. 4. To stop recording, press and release 5 (STOP). The memo is counted as a new message. Recording a Telephone Conversation Once you’ve established a connection with the ...

Page 18 - Turning the Answering System On or Off; When the Memory Is Full; Batteries; About the Handset Batteries; Charging the Handset Batteries

1. After the two-beep signal which indicates that it is ready to accept a command, press and release 6 then #. 2. The system beeps once and “L” will be displayed in the Message Window of the base unit. 3. To stop room monitoring, press and release 5 or hang up. Turning the Answering System On or Off...