AT&T 5635 - Manual
AT&T 5635 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – announcement has not been recorded.; Charge the handset batteries for 10 hours.; Record an announcement.; Telephone Operation; Making Calls
- Page 4 – If You Go Out of Range:
- Page 6 – Memory Dialing; Programming a Number Into Memory
- Page 7 – REDIAL; Programming and Dialing Long Numbers or Sequences; MEM; Changing or Replacing a Stored Number
- Page 8 – Answering System Operation: At The Base; About Mailboxes
- Page 9 – Setting System to Answer Calls
- Page 10 – Message Window
- Page 13 – Screening Incoming Calls; ANNC; Priority Calling; To use Priority Calling,; Answering System Operation: Away from the Base; ANS SYS
- Page 14 – enter your access; (it is not necessary to wait for the announcement to finish.); Reviewing Your Access Code
- Page 16 – The Outgoing Announcement; Reviewing Your Outgoing Announcement; Recording a Memo
- Page 17 – Recording a Telephone Conversation; Call Monitoring; OFF; Call Intercept; PHONE; Room Monitor
- Page 18 – Turning the Answering System On or Off; When the Memory Is Full; Batteries; About the Handset Batteries; Charging the Handset Batteries
CORDLESS ANSWERING SYSTEM 5635
•
•
•
•
•
•
Installation
Table/Desk Installation
1.
Choose a spot near an electrical outlet and a telephone jack.
Your phone requires a modular telephone jack and a standard electrical outlet (110v AC). The outlet
should not be controlled by a wall switch – if the switch is ever turned off, the phone will not operate
properly.
2.
Install the base batteries.
Open the battery door on the bottom of the unit by pulling on the tab. Insert the batteries, making sure
that they are in correctly, then close the door.
The batteries are used to save your messages in the event of a power failure.
When the base batteries need to be replaced, the LO BATT BASE Light on the base will blink.
3.
Set DIAL MODE switch.
Set the DIAL MODE switch on rear of the base unit to TONE if you have touch tone service, or
PULSE if you have dial pulse (rotary) service. To change dial mode during a call, see Temporary
Tone.
4.
Connect the telephone line cord.
The telephone line cord has a snap-in plug on each end. Insert one of the plugs into the jack in the rear
of the base unit. Insert the other plug into a telephone jack. Make sure the plugs snap into place.
5.
Set the HANDSET RINGER switch (ON, OFF).
Set the HANDSET RINGER switch on the base unit to ON so the phone will ring. When the switch is
set to OFF, the phone will not ring.
6.
Fill in the telephone number card.
On the handset, insert a pointed object into the hole in the window, and gently pry up the window until
it pops out. Write your phone number on the card and replace the window.
7.
Install the flexible handset antenna.
The flexible handset antenna has a metal end with a threaded tip. Slide the metal tip straight down
into the hole in the top of the handset. When you feel the antenna reach the bottom of the hole, turn
the antenna clockwise slightly to make sure that the tip is set in place, and then continue to screw the
antenna clockwise until the rubber is snug against the top of the handset. Do not overtighten the
antenna.
8.
Plug in the power cord.
Plug the AC adapter on the power cord into an electrical outlet not controlled by a wall switch. When
you connect the unit to an electrical outlet, the system automatically begins formatting digital memory.
The Message Window begins to count down from 8 to 0. When memory formatting has been
completed,
“0”
will blink in the Message Window to indicate that the system is on, but an
announcement has not been recorded.
9.
Charge the handset batteries for 10 hours.
Place the handset in the base and let the batteries charge for 10 hours. You can use your phone before
the 10 hours are up, but be sure to return the handset to the base so it can charge fully. The
CHARGING Light on the base unit will light to show the batteries are charging.
10.
Check for dial tone.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
sleeve toward the screw head. Insert the screws into the holes you started. Tighten the screws until thesmall end of the mounting sleeve is flat against the wall. 11. Connect the telephone line cord. The telephone line cord has a snap in plug on each end. Insert one of the plugs into the jack in the...
Occasionally, especially when you pick up the handset between rings, you may not be connected. If thishappens, press PHONE on the handset to connect the call.If the handset rings when it’s out of the base, pick up the handset, extend the antenna and press PHONE toanswer the call. Hanging up: To end ...
Using the Intercom During a Phone Call First place the call on hold by pressing HOLD. Then use the intercom. While you are using the intercom, the Phone Lights on the handset and the base will blink to show that your call has not been disconnected.The person on the other end of the phone call will n...
