APC AP7003 - Manuals

1 General Information About NetworkAIR 1000 APC’s NetworkAIR 1000 is a portable, compact, air-conditioner designed for spot-cooling, emergency-cooling, and after-hours cooling of server closets, data centers, conference rooms, home offices, or rooms housing heat-sensitive equipment. The NetworkAIR 1...

2 General Information continued Front View Back View Control Panel HorizontalAir Flow Guides Vertical SwingLouver Handle Water Tank Caster Power Cord & Plug WashableAir Filter Drain Valve Exhaust Vent

3 General Information continued Control Panel Power Turns the unit on and off. Mode Sets the desired operating mode: fan, cooling, or dehumidifying. Fan Speed Sets desired fan speed: high, medium or low. Louver Directs the air distribution. Temperature Sets the desired temperature (61°– 86°F). Timer...

4 General Information continued LCD Indicators Temperature Fan Mode Cooling Mode Dehumidify Mode Louver On Timer On/Off Timer Setting Fan Speed Set Temperature Note: Temperature is shown in Celsius on the AP7004.

5 Installation Warnings Use the unit on a flat surface where the air outlets are unobstructed. Do not place the unit less that 20 inches (50 cm) away from any wall or obstacle. Do not install this air conditioner where there are fumes or flammable gases, or in an extremely humid space such as a gree...

6 Installation continued Check components 1. Check that the condensate tank on the side of the unit is in place and is properly seated. If the tank is not installed properly, the unit will not operate. 2. Open the air filter cover on the left side of the unit and check that the air filter is clean. ...

7 Operation Power Turn the unit on or off by pressing the Power button. Cooling • To select the Cooling mode, press the Mode button until the cooling mode indicator appears in the LCD window. • Set the fan speed by pressing the Fan Speed button. The fan speed indicator in the LCD window will display...

8 Operation continued Timer Your portable air conditioner has a timer feature that allows the unit to shut off or turn on automatically in a preset number of hours. 1. Set Timer On mode a. Make sure mode (cool, dehumidify or fan), tempera- ture, and fan options are on the desired setting. b. Turn th...

9 Installing the Exhaust Kit Installing into ceiling plenum For this installation you will need the following: • The ceiling adapter• The holder flange • The exhaust duct • The base flange Note: There should be about 12 to 15 inches of open space above the ceiling adapter opening so that exhaust air...

11 Drainage Methods of Draining The NetworkAIR 1000 has two methods of disposing of the condensation. The first is a condensate tank that can be manually emptied. The second method is to attach a drain hose to the unit so the water will run to a floor drain. Condensate Tank The condensation will dra...

13 Drainage continued The drainage tube 1. Slide out the drain valve from the left side of the unit. 2. Attach the drainage tube to the drain valve. 3. Route the tubing downward so that condensate flows prop- erly into a floor drain or condensate line below the unit. Note: Condensation will drip thr...

14 Maintaining the Unit Clean the air filter APC recommends cleaning your air filter at least after every two weeks of use. Keeping your air filter clean will maximize the performance and life of this product. 1. Turn off the unit and unplug it from its electrical outlet. 2. Open the air filter on t...

16 Maintaining the Unit continued Storing the Unit The following precautions must be taken when storing the unit for extended periods of time: 1. Turn off unit. 2. Clean the air filter and allow to air dry before replacing in unit. 3. Empty the condensate tank. 4. Remove the stopper from the water d...

17 Troubleshooting Try this first Problem Cause Suggestion Unit does not work Unit is not plugged in. Securely plug receptacle into the wall. Main power is off. Check fuse or circuit breaker Condensate tank is full. Indicator light is on. Empty tank. Poor cooling performance. Air exhaust or intake b...

18 Troubleshooting continued Try this first, continued Problem Cause Suggestion Water is leaking from unit. Drain tube is clogged. Remove blockage. Condensate tank is improperly seated. Reposition tank. Surface not level. Place unit on a level surface away from obstructions. Damaged condensate tank....

19 Troubleshooting continued If problems persist For problems not covered in the troubleshooting chart, or if the problem persists, follow this procedure: 1. Note the serial number and date of purchase of the NetworkAIR 1000. Contact Customer Support at a phone number or address on the back cover of...

20 Warranty Information Limited warranty American Power Conversion (APC) warrants the NetworkAir 1000 to be free from defects in materials and workmanship for a period of one year from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole opti...

21 Specifications Item Specification AP7003 AP7004 Electrical Power source 115 V; 60 Hz 230 V; 50 Hz Rated current 6.2 A 3.6 A Rated input Cooling 692 WDehumidify 660 W Cooling 860 WDehumidify 820 W Physical Condensate Tank capacity 3.5 qt (3.3 L) 3.5 qt (3.3 L) Physical dimensions 12.85×16.250×30.7...

APC Worldwide Customer Support Customer support for this or any other APC product is available at no charge in any of the following ways: • Visit the APC Web site to find answers to frequently asked questions (FAQs), to access documents in the APC knowledge base, and to submit cus-tomer support requ...