APC 1500VA - Manuals - manualsarea.com

Page 3 - Introduction; NSTALLATION; Read the Safety Instruction sheet before installing the UPS.; Unpacking; on servers with permanently attached power cords.; Positioning the UPS

1 Introduction American Power Conversion Corporation (APC) is the leading national and international manufac-turer of state-of-the-art uninterruptible power supplies, redundant switches, power management soft-ware, and related equipment. APC products protect hardware, software, and data from power d...

Page 4 - Connecting Equipment and Power to the UPS; Plug in the battery connector; Note: Do not connect a laser printer to the UPS. A laser; Do not

2 Connecting Equipment and Power to the UPS S MART -UPS R EAR P ANEL 230V M ODELS 120V/100V M ODELS 1. Plug in the battery connector . 2. Connect equipment to the UPS. Note: Do not connect a laser printer to the UPS. A laser printer draws significantly more power than other types of equipment and ma...

Page 5 - Serial Port; Use only interface kits supplied or approved; Use the battery pack connector to connect optional external; See the APC web site,; TVSS Screw

3 B ASIC C ONNECTORS Serial Port USB Port Power management software and interface kits can be used with the UPS. Use only interface kits supplied or approved by APC. Use the APC supplied cable to connect to the Serial Port. DO NOT use a standard serial interface cable since it is incompatible with t...

Page 6 - PERATION; The online

4 2: O PERATION S MART -UPS F RONT P ANEL Power On Power Off Load Battery Charge Online The online LED illuminates when the UPS is supplying utility power to the con- nected equipment. If the LED is not lit, the UPS is either not turned ON, or is sup-plying battery power. AVR Trim This LED illuminat...

Page 7 - On Battery Operation

5 AVR Boost This LED illuminates to indicate the UPS is compensating for a low utility voltage. On Battery When the on battery power LED is lit the UPS is supplying battery power to the connected equipment. When on battery, the UPS sounds an alarm—four beeps every 30 seconds. Overload The LED illumi...

Page 8 - high

6 3: U SER C ONFIGURABLE I TEMS N OTE : S ETTINGS ARE MADE THROUGH SUPPLIED P OWER C HUTE SOFTWARE OR OPTIONAL S MART S LOT ACCESSORY CARDS . F UNCTION F ACTORY D EFAULT U SER S ELECTABLE C HOICES D ESCRIPTION Automatic Self-Test Every 14 days (336 hours) Every 7 days (168 hours), On Startup Only, N...

Page 10 - Storage; for information on re-; Step 1

8 4: S TORAGE , M AINTENANCE , AND T RANSPORTING Storage Store the UPS covered and positioned as for proper functioning, in a cool, dry location, with the bat-teries fully charged. At -15 to +30 ° C (+5 to +86 ° F), charge the UPS battery every six months. At +30 to +45 ° C (+86 to +113 ° F), charge...

Page 12 - To replace the battery module, reverse the directions above for; Disconnecting the Battery for Transport; The battery may remain in the UPS it does not have to be removed.; Shut down and disconnect any equipment attached to the UPS.

10 R EPLACING THE B ATTERY M ODULE To replace the battery module, reverse the directions above for Removing the Front Bezel and Bat- tery Module . Disconnecting the Battery for Transport Always DISCONNECT THE BATTERY before shipping in compliance with U.S. Department of Transportation (DOT) regulati...

Page 13 - ROUBLESHOOTING; , for assistance with complex UPS problems.; replace battery

11 5: T ROUBLESHOOTING Use the chart below to solve minor Smart-UPS installation and operation problems. Refer to the APC web site, www.apc.com , for assistance with complex UPS problems. P ROBLEM AND P OSSIBLE C AUSE S OLUTION UPS WILL NOT TURN ON Battery not connected prop-erly. Check that the bat...

Page 14 - Specifications

12 P ROBLEM AND P OSSIBLE C AUSE S OLUTION T HE OVERLOAD LED IS LIT AND THE UPS EMITS A SUSTAINED ALARM TONE The UPS is overloaded. The connected equipment exceeds the specified “maximum load” as de-fined in Specifications at the APC web site, www.apc.com . The alarm remains on until the overload is...

Page 15 - In order to operate at the full VA rating of the 1500VA; Utility Voltage; Press and hold the

13 P ROBLEM AND P OSSIBLE C AUSE S OLUTION UTILITY CIRCUIT BREAKER TRIPS Utility circuit breaker trips during normal operation. 100V models: In order to operate at the full VA rating of the 1500VA product, the supplied 15A plug must be replaced with a 20A plug. This change must be performed by quali...

Page 16 - Service; Review the problems discussed in the; Contacting APC; Refer to the information provided at the APC Internet site,

14 Service If the UPS requires service do not return it to the dealer. Instead, follow these steps: 1. Review the problems discussed in the Troubleshooting section of this manual to eliminate com- mon problems. 2. If the problem persists, contact APC Customer Service through the APC web site, www.ap...

Page 17 - Regulatory Agency Approvals and Radio Frequency Warnings

15 6: R EGULATORY AND W ARRANTY I NFORMATION Regulatory Agency Approvals and Radio Frequency Warnings 230V MODELS This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take corrective ac-tions. 120V MODELS This equip...