Blomberg WNF 6221 - Manual

6 EN 2 Important safety instructions This section contains safety instructions that will help protect from risk of personal injury or property damage. Failure to follow these instructions shall void any warranty. General safety • This product should not be used by persons with physical, sensory or m...

8 EN 3 Installation Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Authorize...

11 EN install a 13 Amp fuse. • The specified voltage must be equal to your mains voltage. • Do not make connections via extension cables or multi-plugs. B Damaged power cables must be replaced by the Authorized Service Agents. Electrical requirements Before you insert the plug into the wall socket m...

13 EN 4 Preparation Things to be done for energy saving Following information will help you use the product in an ecological and energy- efficient manner. • Operate the product in the highest capacity allowed by the programme you have selected, but do not overload; see, “Programme and consumption ta...

15 EN Using detergent and softener Detergent Drawer The detergent drawer is composed of three compartments: - (1) for prewash - (2) for main wash – (3) for softener – (*) in addition, there is siphon piece in the softener compartment. 1 2 3 1 2 3 C The detergent dispenser may be in two different typ...

17 EN Tips for efficient washing Clothes Light colours and whites Colors Dark colors Delicates/ Woolens/Silks (Recommended temperature range based on soiling level: 40-90C) (Recommended temperature range based on soiling level: cold-40C) (Recommended temperature range based on soiling level: cold-40...

18 EN 5 Operating the product Control panel 1 - Programme Selection knob (Uppermost position On/Off) 2 - Programme Follow-up indicator 3 - Temperature Adjustment button 4 - Spin Speed adjustment button 5 - Auxiliary Function buttons 6 - Delayed Start button (in some models) 7 - Start / Pause button ...

20 EN To decrease the temperature, press the Temperature Adjustment button. Temperature will decrease gradually. C If the programme has not reached the heating step, you can change the temperature without switching the machine to Pause mode. Spin speed selection Whenever a new programme is selected,...

21 EN Programme and consumption table • Selectable * Automatically selected, no canceling. ** Energy Label programme (EN 60456 Ed.3) *** If maximum spin speed of the machine is lower then this value, you can only select up to the maximum spin speed. C Water and power consumption may vary subject to ...

22 EN Auxiliary function selection Use the following auxiliary functions according to your daily needs. Select the desired auxiliary functions before starting the programme. Furthermore, you may also select or cancel auxiliary functions that are suitable to the running programme without pressing the...

23 EN hours delayed start is selected. If you press the Delayed Start button once again, Delayed Start function will be canceled. 4. Press Start / Pause button. Previous delayed start time light turns off and next delayed start time light turns on after every 3 hours. 5. At the end of the countdown,...

24 EN Follow-up indicator. At the beginning of every programme step, the relevant indicator light will turn on and light of the completed step will turn off. You can change the auxiliary functions, speed and temperature settings without stopping the programme flow while the programme is running. To ...

25 EN 6 Maintenance and cleaning Service life of the product extends and frequently faced problems decrease if cleaned at regular intervals. Cleaning the detergent drawer Clean the detergent drawer at regular intervals (every 4-5 washing cycles) as shown below in order to prevent accumulation of pow...

28 EN 7 Troubleshooting Programme cannot be started or selected. • Washing machine has switched to self protection mode due to a supply problem (line voltage, water pressure, etc.). >>> Press and hold Start / Pause / Cancel button for 3 seconds to reset the machine to factory settings. (See...

34 EN 8 Guarantee Your new Blomberg product is guaranteed against the cost of breakdown repairs for 3 years from the date of the original purchase. What is covered? • Repairs necessary as a result of faulty materials, defective components or manufacturing defect. • The cost of functional replacement...

35 EN Please keep your purchase receipt or other proof of purchase in a safe place; you will need to have it should the product require attention under guarantee. You should also complete the details below; it will help us assist you when requesting service. (The model number is printed on the Instr...