Page 2 - Device Overview
2 Device Overview 1 2 3 4 5 6 Device Overview Lucca_long_2G_eng.indd 2 Lucca_long_2G_eng.indd 2 13.04.2006 11:53:30 Uhr 13.04.2006 11:53:30 Uhr
Page 3 - : Opens the start screen of; VOL; Touchscreen: All entries and the
3 The following button are located be-low the display: 1 INFO : Repeats the last travel in- struction. 2 MENU : Opens the start screen of the device. 3 On/Off switch: Short press: Starts the device in the previously used mode or switch-es the device to a state of rest.Long press (longer than three s...
Page 5 - Contents
5 Contents Device Overview ......................2 Safety notes ...........................10 Safety Notes for Navigation ....... 10Safety Notes for Handling the Lucca ........................................ 10 Initial Startup of Lucca ..........11 Lucca Scope of Delivery ............... 11 Protect...
Page 8 - Approaching the Next Destination . 65
8 Contents Additional Functions during Navigation ..............................64 Inserting an Interim Destination ... 64 Approaching the Next Destination . 65 Blocking route segments .......65 Manual Blocking......................... 65Unblocking ................................. 66 Using the TMC ...
Page 10 - Safety Notes for Navigation; Remove the power supply connec-; Safety notes
10 Safety notes For your personal benefi t, please carefully read the following safety notes and warnings before operating your Lucca for the fi rst time. Safety Notes for Navigation Caution: Do not operate the Lucca while driv-ing to protect yourself and others against accidents!View the display on...
Page 11 - Initial Startup of Lucca; Lucca Scope of Delivery; Initial Startup
11 constantly uses electricity and could discharge the vehicle bat-tery. • Do not unplug the connector by pulling on the wire. The wire could be damaged! • Do not use harsh solvents to clean the device; use only a damp, lint-free cloth. Initial Startup of Lucca If you are starting up the Lucca for t...
Page 12 - Protective Films and Covers; ON
12 Protective Films and Covers Prior to the initial use, remove the protective fi lms from the display and front of the housing. Before using the cradle, please remove the elastic cover at the bottom of the housing. Before inserting an SD card, please remove the dummy card. To protect the contacts, ...
Page 13 - Setting the Language; Settings; Reset; Charging the Battery
13 Setting the Language If the Lucca was switched off using the main switch, US English is used as the standard language. If neces-sary, you may have to set the desired language for the menus and the voice output: ➜ Switch on the Lucca using the On/Off switch . ➜ Touch Settings . Touch or until Lang...
Page 16 - for longer than; Note
16 ➜ Carefully push the guide of the Lucca over the track of the suction cup holder. Installing Lucca in the Cradle The cradle features a track for mount-ing the Lucca on the inside. ➜ Carefully push the guide of the Lucca over the track of the suction cup holder. Removing the Lucca ➜ Pull the Lucca...
Page 17 - Software Keyboard; Entering Blank Spaces; Lists; Operating the Navigation Menus
17 Operating the Navigation Menus Software Keyboard If text entries are required, the touch-screen displays a software keyboard. You can perform all entries using your fi nger. Only capital letters can be en-tered.You do not have to enter any special characters or umlauts when entering city or stree...
Page 18 - Buttons; Navigation
18 This is the case, for example, if you do not enter the complete name of a place during the entry. After every en-try of a letter, the text fi eld shows the fi rst entry that starts with the previ-ously entered characters. To display a list with additional matching entries, touch the List button. ...
Page 19 - More; : Touch this button to obtain; Information; From the; Traffi c Jam Reports; In the; Traffi c jam reports; The
19 punkt start screen (Lucca MP3 only). Here, you can open another application, such as the MP3 play-er or the Picture Viewer, or reopen the navigation. • More : Touch this button to obtain access to additional functions. De-pending on the menu in which this button is located, different func-tions a...
Page 22 - Starting the Navigation; Switch on the device using the
22 Navigation General Notes about the Navigation The use of the Lucca is at your own risk. Caution: Do not operate the Lucca while driv-ing to protect yourself and others against accidents!View the display only if you are in a safe travel situation!The street routing and traffi c signs have priority...
Page 24 - Performing Basic Settings
24 Exiting the Menu (Lucca MP3 only) ➜ In the Navigation menu, touch to quit the navigation. The Lucca start screen displays. Additional Functions ➜ Touch the More button to gain ac- cess to additional functions of the Navigation . The list of additional functions dis-plays. It contains the followin...
Page 26 - Specifying a Destination
26 ➜ Touch the Enter your home ad- dress button. The Destination entry menu dis- plays. ➜ Touch the Address button and en- ter your home address. See "En-tering a Destination Address". ➜ Touch the Set as home address button. The address is copied into the Home address menu. ➜ Touch the OK bu...
Page 27 - Destination entry; Country; Destination entry
27 Entering a Destination Country First, enter the country in which your destination is located. Note: This entry does not have to be repeated. If your destination is in a different country than the pre-vious one, you must re-enter the country. ➜ In the main menu (Lucca MP3 only) touch the Navigatio...
Page 28 - Address
28 Note: You can only select countries which are at least partially displayed on the currently loaded map. Entering a Destination Address ➜ In the main menu (Lucca MP3 only) touch the Navigation but- ton. The Navigation menu displays. ➜ In the Navigation menu, touch the Destination entry button. The...
Page 29 - Selecting a Point of Interest
29 Intersection fi eld to enter the crossroad to the defi ned street. Note: How to save a defi ned destination is described in the chapter "Saving one of the recent destinations". Additional Functions ➜ Touch the More button to gain ac- cess to additional functions of the Address menu. The l...
Page 30 - Points of interest; Point of interest
30 ➜ In the main menu (Lucca MP3 only) touch the Navigation but- ton. The Navigation menu displays. ➜ In the Navigation menu, touch the Destination entry button. The Destination entry menu dis- plays. ➜ Touch the Points of interest but- ton. The Point of interest menu dis- plays. ➜ Touch the ... nea...
Page 38 - Itinerary; Interim destination
38 Notes: – This function is only available with GPS reception. – If you use this function during a navigation, all previously de-fi ned route locations (stages and destination points) are de-leted! • Touch the Save button to save the selected destination. You can select the destination at any time ...
Page 42 - Managing Destinations; Saving Destinations
42 The route calculation is performed and the navigation starts. Note: The route type used for the route calculation is automatically select-ed from the setting which you de-fi ned in the Routing options menu. Managing Destinations Two lists are available in which indi-vidual destinations are saved:...
Page 46 - Add; Adding a Route Point; Destination Entry; Route Planning
46 The Destination entry menu dis- plays. ➜ Defi ne the route point similar to the destination entry. For more in-formation, see the chapter "Enter-ing a Destination". ➜ Touch the Add button. The Itinerary menu displays. The defi ned destination is listed as route point 1. ➜ Repeat the steps...
Page 50 - Routing options
50 The Routing options menu dis- plays. ➜ Touch the Speed profi le fi eld to change between the available pro-fi les. ➜ Touch the Type of routing fi eld to change between the various modes: • Dynamic route (TMC)– This option requires that an external TMC receiver is con-nected. With this option, tra...
Page 51 - Favourites; Start navigation; The route is being calculated.; Destination Guidance
51 Destination Guidance Prerequisite: • You specifi ed a place of destina-tion as described in the chapter "Entering a Destination" - or - • you selected a place of destination from the Favourites as described in the chapter "Copying the Destina-tion from the Favourites" - or - • you...
Page 52 - Reaching the Place of Destination
52 Disturbed GPS Reception A message appears after entering the destination if no adequate GPS signal is received. You have the following options: • Open the battery cover and en- sure that the switch inside is set to "ON". • If you are in an enclosed room, move to the outside. The Lucca re-...
Page 53 - Working with the Map; Map Operation
53 Working with the Map Map Operation In this section you learn which in-formation and which processing op-tions are available in the map view. Depending on whether you display a map without or during the navigation, different options are available for op-eration. Showing a Map You can display the m...
Page 58 - Route Options; Route options; button to; Next Destination; Touch the; Next destination; The route is recalculated so that
58 Afterwards, all subsequent route points are selected. For further details, please read the section "Inserting an Interim Destina-tion". Route Options ➜ Touch the Route options button to change the route options. For further details, please read the section "Routing options". Next ...
Page 60 - – The more yellow bars are dis-; Route Information; : This symbol represents; Signpost Information
60 – The more yellow bars are dis- played, the closer you are to the location of the next action. • The upper street fi eld displays the next street name. • The lower street fi eld displays the current street name. Route Information The right area of the map displays the following route information:...
Page 66 - Block road; Select the; Block road
66 Supposing that you are on the mo-torways and hear a traffi c announce-ment on the radio about a traffi c jam of 5 km on your route. In this case, you can use a manual blocking of the section to evade the traffi c jam.The manual blocking is only applica-ble to the current navigation and is no long...
Page 67 - Using the TMC Functionality; Traffi c Reports with TMC
67 Using the TMC Functionality Traffi c Reports with TMC The Traffi c Message Channel (TMC) supplies your Lucca with traffi c re-ports. This is made possible by a Blaupunkt car sound system with TMC receiver that receives the traffi c reports broadcast by the radio sta-tions. TMC Mode of Operation T...
Page 71 - Map Information; Confi guring Lucca
71 Map Information In the Map information menu, you can perform the following settings: • Info bar– If you activate the entry, the compass, altitude and current speed are displayed on the map in the lower right border. • Points of interest– If you activate the entry, the map displays all the points ...
Page 76 - GPS Mode of Operation
76 Home Address In the Home address menu, you can store your home address so that you can quickly navigate home from any location. ➜ Touch the Enter your home ad- dress button. ➜ Touch the Address button and enter your home address in the "Entering a destination address" section. ➜ Touch the...
Page 77 - Preparing the SD Card; Mode
77 If the Lucca receives the signals from at least 3 satellites, it can determine its position and display it on the map. This position can then be used as the starting point for a route calculation. Since a positioning and position dis-play is carried out once every second, you can view your moveme...
Page 78 - MENU; Starting Playback; Music
78 Inserting the SD Card The SD card slot is located on the right side of the Lucca MP3. ➜ Push the SD card into the SD card slot according to the marking on the slot until the card engages. Selecting MP3/WMA Mode If you are in a different operating mode, ➜ press the MENU button below the display to...
Page 79 - Selecting a Directory via Button; Selecting Tracks/Files
79 Selecting a Directory via Button ➜ To select the next higher direc-tory, touch the button in the Music menu. ➜ To select the next lower directory, touch the button in the Music menu. Selecting a Directory via File Browser ➜ In the Music menu, touch the More button. The menu with the additional fu...
Page 80 - Selecting a Track via Button; Confi guring the Display
80 Selecting a Track via Button ➜ To select the next track in the di-rectory, touch the button in the Music menu. ➜ To select the previous track in the directory, touch the button in the Music menu. The next or previous track starts playing. Confi guring the Display You ca defi ne whether the tracks...
Page 81 - Quitting Playback
81 Repeated Directory Play (Repeat) You can repeatedly play all the tracks of a directory. ➜ In the Music menu, touch the More button. ➜ Touch the Repeat button. The function is activated if a check mark is displayed behind Repeat . ➜ Touch the button. The Music menu is displayed again. Quitting Pla...
Page 82 - Removing the SD Card; button in the; Starting the Picture Viewer; press the; button below the; Picture Viewer
82 Removing the SD Card ➜ You quit the MP3/WMA mode by touching the button in the Music menu. ➜ Carefully push on the SD card in the slot until it disengages. The SD card is ejected a little bit and can be removed. Picture Viewer (with Lucca MP3 only) The Lucca MP3 can also be used to view pictures ...
Page 83 - Starting the Slide Show; Pictures
83 ➜ Touch the Picture Viewer button. The Pictures menu displays. The fi rst picture in the fi rst direc- tory recognised by the Lucca MP3 is displayed. Starting the Slide Show If you started the Picture Viewer, the fi rst picture in the fi rst directory recognised by the Lucca MP3 is dis-played. ➜ ...
Page 84 - Slideshow; Quitting the Slide Show
84 ➜ Touch the Slideshow button re- peatedly until the desired time is displayed. ➜ Touch the button. The Pictures menu is displayed again. Quitting the Slide Show ➜ To quit the slide show, touch any position on the display. The slide show is stopped and the Pictures menu is displayed again. Selecti...
Page 85 - Selecting a Picture; Selecting a Picture via Button
85 ➜ Touch the desired directory. The directory is displayed. ➜ Touch the picture you want to dis-play. The Pictures menu is displayed again and the selected picture is displayed. Selecting a Picture You can select titles by using the but-tons in the Pictures menu or by using the fi le browser. How ...
Page 86 - Show Folder
86 ➜ Touch the Show Folder button. The display of the directory name is activated if a check mark is dis-played. ➜ Touch the button. The Pictures menu is displayed again. Adjusting the Picture to the Display Format You can defi ne that pictures which are stored in portrait format, are au-tomatically...
Page 87 - Installing Street Maps
87 Installing Street Maps The road map of the country in which the Lucca was purchased is prein-stalled in the memory of the Lucca. You can purchase additional road maps for most European countries on SD card or CD-ROM.The preinstalled road map is also contained on the enclosed CD-ROM for a future r...
Page 88 - Cradle; Accessories
88 Accessories Cradle (only Lucca MP3 is part of the scope of delivery)The cradle allows for adding addi-tional functions to the Lucca. If you installed the cradle in your ve-hicle and connected it to a Blaupunkt car sound system, the following func-tions are available: • TMC data transfer to the Lu...
Page 89 - NF in –
89 Connection Blocks of Blaupunkt Car Sound Systems for Lucca MP3 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 C B A 1 4 7 10 13 16 19 3 6 9 12 15 18 2 5 8 11 14 17 20 C-1 C-2 C-3 A B 1 nc 1 Speaker out RR+ 2 Radio Mute 2 Speaker out RR- 3 Sub out 3 Speaker out RF+ 4 Permanent +12V 4 Speaker out RF- 5 Aut. anten...
Page 90 - OK; TMC; Installations
90 Installations (not part of the scope of delivery) Steering Wheel Remote Control RC 09 The RC 09 steering wheel remote control allows you to operate the Lucca safely and conveniently from your steering wheel. • With the buttons , , and , you can move the selection mark (yellow) in the menus and li...
Page 91 - Technical Data; Warranty; Blaupunkt GmbH, Hotline; Disposal of old unit; Do not dispose of your old unit in
91 Technical Data TFT display Active colour matrix, 3.5 inch diagonal, 320 x 240 pixel Audio Built-in loudspeaker: Mono, 8 Ohm, max 2 W rms Audio output via cradle: Stereo, V max =1 V eff , R typ =600 Ohm Battery Voltage: 3.7 VCapacity: 2000 mA Cigarette lighter wire Input voltage: 12 to 24 VFuse in...
Page 93 - FAQ
93 The built-in loudspeaker does not meet my quality demands. What can I do? The Lucca can be connected to a car sound system with Tel.-In/Aux-In, so that the loudspeakers can be used for the playback. The sound should improve signifi cantly. In which countries is TMC reception possible? The followi...