BISSELL 3676 - User Manual

Meet your new BISSELL product!

Go to

support.BISSELL.com

for a comprehensive walkthrough

of your new purchase, including videos, tips, support, and more.
Want to get started right away? This guide has all the information
you need to set up your new product. Let’s take a look…

6

BISSELL.com

BISSELL.com

3

Product Overview

1. Handle
2. Stretch Hose
3. Wand Release Button
4. Tank Release Button
5. Carry Handle
6. Dirt Tank

7. Cord Rewind Button
8. Power Pedal
9. Recline Pedal
10. Height Adjustment

Important Safety Instructions ................................ 2

Warranty ............................................................................... 2

What’s in the Box? ......................................................... 2

Assembly .............................................................................. 3

Using the Vacuum .......................................................... 3

Emptying the Dirt Tank............................................... 5

Cleaning the Pre-Motor Filter ................................. 5

Maintaining Your Vacuum .........................................6

Troubleshooting ...............................................................6

CLEANVIEW® REWIND

U PRIG HT VACU U M

MODEL S 353 4 , 3675 , 3676

1

2

5

6

8

9

3

4

10

7

Assembly

Go to

support.BISSELL.com

for assembly videos.

1.

Attach wand to vacuum base.

2.

Attach stretch hose to

wand and twist clockwise to

lock into place.

3.

Attach stretch hose to back

of vacuum and twist clockwise

to lock into place.

4.

Attach hose clip to body of

vacuum by sliding up until it

clicks into place. Remove hose

clip for extended cleaning

reach when in use.

5.

The hose should sit on the

vacuum without any twists.

6.

Attach tools to tool holders.

Using the Vacuum

For additional support videos and information, visit

support.BISSELL.com

.

WARNING

• To reduce the risk of electric shock, turn power OFF and disconnect plug from electrical outlet before performing maintenance or

troubleshooting checks.

• Do not operate vacuum with damp or wet filters or without all filters in place.

Maintaining Your Vacuum

For more helpful maintenance tips, check out

support.BISSELL.com

.

Maintaining the TurboBrush® Tool

1.

Twist gray collar counterclockwise until slot

appears; separate faceplate and remove brush.

Replace belt and brush if needed.

2.

If paddle wheel is dislodged, align two clips on

each side and click into place.

3.

Faceplate will not close if all parts are not

aligned correctly.

Clearing a Clog

1.

Remove hose from back of vacuum by twisting

left. Remove any debris.

2.

Check foot hose on back of vacuum, towards

the bottom. If necessary, remove screw from foot

hose and check for clogs.

3.

Check air passageway on the bottom of

vacuum. Remove bottom cover and brush.

Remove any debris.

Replacing the Brush and Belt

1.

Unplug vacuum, turn over and unscrew six

Phillips-head screws to remove bottom cover.

2.

Lift brush roll straight out. Inspect belt,

replace if it appears damaged.

3.

If belt is not broken. Inspect brush roll by

placing it on its end and spinning. Brush roll

should spin freely, multiple times with one flick.

Replace brush roll if it doesn’t spin freely.

4.

Replace brush roll and belt by looping belt

over motor shaft and brush roll. Line up endcaps

and pull brush forward into place. Belt will

stretch.

5.

Once brush roll is installed, place bottom

cover back on and replace screws.

©2022 BISSELL Inc. All rights reserved.

Part Number 1630631 07/22 RevH

Every Purchase Saves Pets

™

BISSELL proudly supports BISSELL Pet Foundation® and its mission to help save homeless pets.

When you buy a BISSELL® product, you help save pets, too. We’re proud to design products that help

make pet messes, odors and pet homelessness disappear. Visit

BISSELLsavespets.com

to learn more.

For a comprehensive walkthrough of your product and support tips, visit

support.BISSELL.com

.

Troubleshooting

Cleaning the Pre-Motor Filter (continued)

1.

Reinstall foam filter and

close lid.

2.

Place tank back on vacuum

and press firmly until it clicks

into place.

1.

Gently pull the cord out,

stopping at the yellow mark

on the cord. Do not pull past

the red mark.

2.

Press the red power button

with your foot to turn the

vacuum ON

and OFF .

3.

Press the recline pedal and

pull handle back towards you.