Audiovox Pro9544FT3 - Manual
Audiovox Pro9544FT3 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION OF MAJOR COMPONENTS
- Page 3 – WIRING THE SYSTEM; Large 8 Pin Edge Connector:
- Page 4 – some remote start trigger inputs, will damage the control module.; Wiring The 11 Pin Mini Edge Connector:; trunk release circuits will damage the control module.; be active as long as the transmitter button is depressed.
- Page 7 – COMPLETING THE INSTALLATION
SELECTABLE FEATURES
Note: The method of manual override can either be selected to operate from the valet switch or operate
as custom code. Be certain to place a check mark indicating the method used in the box located
on the last page of the owner's manual.
Note: When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s
door pin switch in order to begin the passive arming sequence.
RF Programmable Features :
Feature Selection
1 Chirp
2 Chirps
3 Chirps
4 Chirps
Default
1st DoorL/UL
1 Sec.
3.5 Sec.
1 Sec L, Dbl. U/L
1 Sec.
2nd Accy Lock
Auto Lock On
Auto Lock Off
Auto Lock Off
3rd Accy. UL
Auto UL Dr
Auto UL All
Auto UL Off
Auto UL Off
4th Headlights
On Arm
On Disarm
On Both
Off
Both
5th Passive Locks
Passive
Active
Active
6th Passive/Active Arm
Passive Arm
Active Arm
Active Arm
7th Voltage Sense
Voltage Sense
Hardwire
Hardwire
8th Siren/Horn
Siren/Horn
Siren Only
Horn Only
Siren/Horn
9th Horn Chirp
10mS
16mS
30mS
16mS
10th Override Method
Custom Code
Valet
Valet
11th Chirp Delete From Tx
On
Off
Off
To program these selectable features;
Action
System Response
Turn ignition on
No response
Press and release the valet switch 3 times 1 Chirp - LED 1 flash
Within 3 seconds, turn ignition Off
Short chirp, then long chirp
First
Then On
1 chirp = 1 second door locks
Press transmitter Lock button to change
2 chirps = 3.5 second door locks
Press transmitter Lock button to change
3 chirps = 1 sec. lock, dbl 1 sec. unlock
or
Second
Press and release the valet switch
2 chirps = auto locks off
Press transmitter Lock button to change
1 chirp = auto locks on
or
Third
Press and release the valet switch
3 chirps = auto unlock off
Press transmitter Lock button to change
1 chirp = auto unlock drivers door only
Press transmitter Lock button to change
2 chirps = auto unlock all doors
or
Fourth
Press and release the valet switch
3 chirps = headlight output when arming and disarming
Press transmitter Lock button to change
4 chirps = headlight output off
Press transmitter Lock button to change
1 chirp = headlight output when arming
Press transmitter Lock button to change
2 chirps = headlight output when disarming
or
Model PRO 9544FT3
Installation Manual
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 Fifth Press and release the valet switch 2 chirps = active locks Press transmitter Lock button to change 1 chirp = passive locks or Sixth Press and release the valet switch 2 chirps = active arming Press transmitter Lock button to change 1 chirp = passive arming or Seventh Press and release t...
Page 3 the dash, located where it can be easily seen from outside the vehicle, yet not be distracting to the driver.Once a location has been selected, check behind the panel for wire routing access, and to confirm the drillwill not damage any existing components as it passes through the panel.Drill ...
Dark Blue Wire: DELAYED 300 mA PULSED OUTPUT / CHANNEL 3The dark blue wire pulses to ground via an independent RF channel from the keychain transmitter. This isa transistorized, low current output, and should only be used to drive an external relay coil.WARNING: Connecting the dark blue wire to the ...
