Audiovox PRO-9342FT3 - Manual
Audiovox PRO-9342FT3 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION OF MAJOR COMPONENTS
- Page 3 – WIRING THE SYSTEM; Large 15 Pin Edge Connector:; some remote start trigger inputs will damage the control module.
- Page 7 – COMPLETING THE INSTALLATION; Adjusting the Optional Shock Sensor :; Using a small screwdriver, gently turn the adjustment screw fully
Model PRO-9342FT3
Installation Manual
Note: When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s
door pin switch in order to begin the passive arming sequence.
RF Programmable Features :
Feature Selection
1 Chirp
2 Chirps
3 Chirps
4 Chirps
Default
1st Door L/UL
1 Sec.
3.5 Sec.
1 Sec L, Dbl. U/L
1 Sec.
2nd Accy Lock
Auto Lock On
Auto Lock Off
Auto Lock Off
3rd Accy. UL
Auto UL Dr.
Auto UL All
Auto UL Off
Auto UL Off
4th Passive Locks
Passive
Active
Active
5th Passive/Active Arm
Passive Arm
Active Arm
Active Arm
6th Voltage Sense
Voltage Sense
Hardwire
Hardwire
7th Siren/Horn
Siren/Horn
Siren Only
Horn Only
Siren/Horn
8th Horn Chirp
10mS
16mS
30mS
16mS
9th Override Method
Custom Code
Valet
Valet
10th Chirp Delete From Tx On
Off
Off
To program these selectable features;
Action
System Response
Turn ignition on
No response
Press and release the valet switch 3 times
1 Chirp - LED 1 flash
Within 3 seconds, turn ignition Off
Short chirp, then long chirp
First
Then On
1 chirp = 1 second door locks
Press transmitter Lock button to change
2 chirps = 3.5 second door locks
Press transmitter Lock button to change
3 chirps = 1 sec. lock, dbl 1 sec. unlock
or
Second
Press and release the valet switch
2 chirps = auto locks off
Press transmitter Lock button to change
1 chirp = auto locks on
or
Third
Press and release the valet switch
3 chirps = auto unlock off
Press transmitter Lock button to change
1 chirp = auto unlock drivers door only
Press transmitter Lock button to change
2 chirps = auto unlock all doors
or
Fourth
Press and release the valet switch
2 chirps = active locks
Press transmitter Lock button to change
1 chirp = passive locks
or
Fifth
Press and release the valet switch
2 chirps = active arming
Press transmitter Lock button to change
1 chirp = passive arming
or
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 Sixth Press and release the valet switch 2 chirps = hardwire Press transmitter Lock button to change 1 chirp = voltage sense or Seventh Press and release the valet switch 1 chirp = siren and horn output Press transmitter Lock button to change 2 chirps = siren output only Press transmitter loc...
Page 3 Dash Mounted LED:A small red LED is included that will serve as a visual indicator of the alarm status. It should be installed inthe dash, located where it can be easily seen from outside the vehicle, yet not be distracting to the driver.Once a location has been selected, check behind the pan...
Page 7 output. Connect this wire to the drivers door unlock relay that requires a low current positive signal tounlock only the drivers door. If the vehicle does not have a separate drivers door relay, one will have to beadded. Locate the drivers door unlock motor wire and cut it at a convenient loc...
