Audiovox AA-RS40CS - Manual
Audiovox AA-RS40CS – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION OF THE MAJOR COMPONENTS:
- Page 5 – YELLOW START WIRE DETAIL
- Page 8 – General Motors VATS By-Pass Diagram; the key's value from the resistor pack supplied.
- Page 13 – WIRING THE 4 PIN AUXILIARY OUTPUT HARNESS
- Page 14 – Wire Ground Switched Door Lock/Unlock Wiring Detail
- Page 15 – Wire Positive Switched Door Lock/Unlock Wiring Detail; ALARM SELECTABLE FEATURES
- Page 16 – To Program The Alarm's Selectable Features:
- Page 17 – To Program The Remote Start Selectable Features:; verifying you are in the feature program mode.; REMOTE START SELECTABLE FEATURES; RF Programmable Features:
- Page 19 – TESTING YOUR INSTALLATION:; DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE
- Page 20 – turn the ignition switch off. DO NOT attempt to remove the key.; REMEMBER TO RECONNECT THE BROWN/BLACK WIRE TEMPORARILY
- Page 21 – OF THE NEUTRAL SAFETY START FEATURE.
- Page 22 – METHOD 1; To connect to the key in sensor as shown in method 1:
- Page 23 – METHOD 2; To connect to the key in sensor circuit as shown for method 2:; COMPLETING THE INSTALLATION:; these mechanisms and impair the safe operation of the vehicle.
- Page 24 – WIRING DIAGRAM
Model AA-RS40CS
Installation Manual
This Unit Is Intended For Installation In Vehicles With
12 Volt Negative Ground Electrical Systems,
Gasoline Or Diesel With True Tach Reference
And Automatic Transmissions Only.
Kit Contents:
Remote Start/Alarm Control Module
(2) - Three Button Anti Code Grabbing Transmitters
3 Channel Code Learning Receiver
External Superheterodyne Antenna/Receiver
Mini Six Tone Siren
(1) - Multi Pin Input/Output Harness
(1) - Six Pin Power Harness
(1) - Four Pin Auxiliary Output Harness
(1) - Two Pin LED Indicator
(1) - Two Pin Valet / Programming Switch
(1) - Two Pin Control Switch
(1) - Four Pin Shock Sensor Harness
(1) - Two Pin Door Lock Harness
(1) - Dual Stage Shock Sensor
(1) - Starter Inhibit Relay and Socket
(2) - 30 Amp In-line Fuse Holders With Fuses
(1) - Pin Switch Hardware Bag
(2) - Under Hood Caution Labels
(1) - Installation Manual
(1) - Operator's Manual
(1) - Limited Warranty
(2) - Window Decals
4 Channel Remote Car Starter
With Full Feature Alarm System
Installation Instructions
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
The AA-RS40CS Remote Start/Alarm System is designed to be used with Automatic TransmissionVehicles Only! The unit provides a selectable ignition control that allows a 10 second output for glowplug pre-heat which may be required for certain diesel vehicles, (see selectable feature #9). If the diesele...
5 assure that the vehicle cannot start via RF control in any gear selection other than park or neutral.In both mechanical and electrical neutral start switch configurations, the connection of the Yellow wirewill be made to the low current start solenoid wire of the ignition switch harness. This wire...
General Motors VATS By-Pass Diagram 8 Light Blue Wire: Ignition 3 OutputThis wire provides a 300mA ground output that becomes active 3 seconds before the Remote StartUnit initializes, and remains grounded while running plus an additional 4 seconds after the Remote StartUnit turns off. In all of the ...
