Audiovox AA-RS30CS - Manual

Audiovox AA-RS30CS

Audiovox AA-RS30CS – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
Page: / 20

Table of Contents:

  • Page 2 – INSTALLATION OF THE MAJOR COMPONENTS:
  • Page 3 – WIRING THE 6 PIN MAIN POWER HARNESS:
  • Page 4 – SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.
  • Page 5 – WIRING CONNECTIONS: 12 Pin Input / Output Harness
  • Page 6 – IT IS PRESENTLY CONNECTED TO IN THE VEHICLE.; Brake Switch Positive Shutdown Detail
  • Page 7 – General Motors VATS By-Pass Diagram
  • Page 10 – Blue and Green w/Black Trace Wires - 2 Pin Accessory Output Harness; remote start trigger inputs, will damage the control module.; Channel 2 Relay Wiring Detail
  • Page 11 – Entry Illumination Detail; will damage the control module.
  • Page 12 – connect the tach input wire.; To program these selectable features:; the programming will be terminated.
  • Page 13 – TIMED START OPERATION:
  • Page 14 – DO NOT RELEASE THIS VEHICLE TO THE CONSUMER UNTIL YOU CONFIRM THE; NEUTRAL START SAFETY TEST:; switch off. DO NOT attempt to remove the key.
  • Page 16 – METHOD 1
  • Page 17 – METHOD 2
  • Page 18 – COMPLETING THE INSTALLATION:; under the dash board or in the engine compartment areas.
  • Page 19 – WIRING DIAGRAM
Loading the manual

Model AA-RS30CS

Installation Manual

This Unit is Intended for Installation in Vehicles with

12 Volt Negative Ground Electrical Systems,

Gasoline or Diesel with True Tach Reference

and Automatic Transmissions Only.

Kit Contents

AARS-30CS Control Module

(2) - 3 Button Anti Code Grabbing Transmitters

3 Channel Code Learning Receiver

External Superheterodyne Antenna/Receiver

(1) - Multi Pin Input/Output Harness

(1) - Six Pin Power Harness

(1) - Four Pin Auxiliary Harness

(1) - Two Pin I/O Harness

(1) - Accessory 2 Pin Connector

(1) - 2 Pin Door Lock Harness

(2) - 30 Amp In-line Fuse Holders With Fuses

(1) - Control Switch

(1) - Programming Switch

(1) - Ring Terminal

(4) - 1/2" Long Screws

(1) - Pin Switch

(1) - Remote Start Warning Label

(1) - Literature Package

3 Channel Remote Start / Keyless Entry System

Installation Instructions

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - INSTALLATION OF THE MAJOR COMPONENTS:

The AA-RS30CS is Remote Start/Keyless Entry System is designed to be used with Automatic Transmission VehiclesOnly! The unit provides a selectable ignition control that allows a 10 second output for glow plug pre-heat which maybe required for certain diesel vehicles, (see selectable feature #9). If ...

Page 3 - WIRING THE 6 PIN MAIN POWER HARNESS:

3 Drill a 1/4" hole in the desired location and mount the switch by passing it through the panel from the underside.Secure the switch using the nut, star washer, and on/off face plate. It is suggested that the switch be oriented to allowthe on position to be up toward the driver and the off posi...

Page 4 - SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.

SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS. 4 BLUE Wire: Ignition 1 OutputConnect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 volts when the ignition keyis turned to the to the "ON" or "RUN" and the "START" or CRANK" positions...

Other Audiovox Models