Audiovox 128-7853 - Manual
Audiovox 128-7853 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 5 – Wiring The 4 Pin Auxiliary Output Harness, Connector “A”; Pulsed Ground Output Before Start
- Page 11 – Wire Ground Switched Door Lock Circuits:
- Page 13 – Setting Up The System Programming Features:
- Page 15 – changed. To change, the above sequence will have to be followed.; TIMED START OPERATION:; To learn the light delay, start with all doors closed:
128-7853
1 of 16
1
Model APS-920
Installation Manual
This Remote Start/Alarm System is designed to be used with
Automatic Transmission- Fuel Injection Vehicles Only!
COMPONENTS:
Control Module
1 Four Button RF Transmitter
1 Four Button LCD Transmitter
2 Way Antenna/Receiver
1 “1 X 1.75” Foam Pad
6 Pin Main Power Harness w/Fuses
20 Pin Accessory Harness
1 Hood Pin Switch
1/4” Female Spade Connector
2 Pin Door Lock/Unlock Harness
Starter Inhibit Relay & Harness
2 Pin LED Assy
2 Pin Push-Button Valet/Program Switch
4 Pin Antenna Receivers Harness
4 Pin Auxiliary Output Harness
Installation/Owners Guide
4 Philips Head Black Drill Point Sheet
Metal Screw #8 X 1/2"
FEATURES:
Selectable Ignition Lock & Unlock
Selectable Door Lock/Unlock Output Timing
Safe Start (Requires double push of the start button to engage the remote start function)
On Board Parking Light Relay
Trunk Release Output
Horn Chirp Output With Duration Select
Selectable RF Start Chirp
Panic Mode (Can select to have horn along with parking lights)
Selectable Run Times 5, 10, 15, or 20 Minutes
Selectable Gas or Diesel
Automatic Start Timer (Can be set to start your car automatically at 2 or 4 hour intervals)
4 Negative Pulsed Aux Outputs Before Start, After Start, During Crank, After Shut Down
(To aid installation in many vehicles with factory alarm systems)
Turbo Timer
Dual Stage Shock Sensor
Shock Sensor Shunt During R/S Selectable
FCC NOTICE
This device complies with part 15 of the FCC rules. Operation of this device is subject to the
following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for
compliance voids the users authority to operate this device.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
128-7853 5 of 16 5 BLUE Wire: Ignition 1 Output Connect this wire to the ignition 1 wire from the ignition switch. This wire will show +12 voltswhen the ignition key is turned to the "ON" or "RUN" and the "START" or CRANK" positions, andwill have 0 volts when the key is t...
128-7853 11 of 16 11 4 Pin Shock Sensor Connector “D” Red, Black Green & Blue wires of the shock sensor harness provide +12 Volts, Ground, FullTrigger, and Pre-Detect inputs to and from the sensor. Route these wires from the previouslyinstalled sensor and connect to the mating connector on the c...
128-7853 13 of 16 13 Setting Up The System Programming Features: Bank 1 Transmitter ChannelsStart with the system disarmed, tun the ignition switch to the on position then:1) Press and release the push button valet/program switch 3 times.Siren Chirps once and or Lights flash one time indicating the ...
