AT&T 1817 - Manual - manualsarea.com

Page 2 - I N S T A L L A T I O N

Set Dial Mode This telephone comes set for touch tonedialing. Use the Dial Mode switch on thebottom of the phone to select TT (touch tone) or DP (dial pulse), depending on your service. When set to Dial Pulse mode, thephone can be switched temporarily toTouch Tone mode for access to services thatreq...

Page 3 - Wall Installation

Wall Installation 1 Remove the base. Slide the base sideways as shown bythe REMOVE arrow (Figure 1). 2 Connect the short line cord to thetelephone. Plug the five inch line cord into the LINE jack in the center of the bottom of the set. 3 Reinstall the base. Turn the base so that the larger end istow...

Page 4 - T E L E P H O N E O P E R A T I O N; T E L E P H O N E M E M O R Y

Redial This telephone always stores in memorythe last number manually dialed (up to 24digits). The number remains in memoryuntil you dial another number. To dial the last number called from thisphone, lift the handset and press R . Flash The F button is useful if you subscribe to custom-calling serv...

Page 5 - I N C A S E O F D I F F I C U L T Y

If you have difficulty operating thistelephone answering system, try thesuggestions below. For Customer Service,visit our website at www.telephones.att.com or call 1 800 222–3111. Please retain your receipt as your proof of purchase. No Dial Tone Make sure all plugs are connectedproperly. Check the ...

Page 7 - Setting the Clock; Recording Your Announcement; ANSWERING SYSTEM OPERATION

Setting the Clock You’ll need to set the clock so that it canannounce the day and time that eachmessage is received. Press P to exit Setting the Clock at any time. 1 Press and hold C until the Message Window displays C , and the default day is announced. 2 To change the day setting, hold down or unt...

Page 9 - Listening to Your Messages; Saving Messages

Remote Access Code You can use many features of thisanswering system remotely from a touchtone phone. Most features can beaccessed only after you enter a RemoteAccess Code, which is preset to 123. Youcan review the Remote Access Code bypressing and releasing S . You can change the Remote Access Code...

Page 10 - Deleting Messages; Recording a Memo

Deleting Messages Delete All messages Hold down D . The system announces “ Messages deleted ” and permanently deletes messages. The Message Windowdisplays 0 . If you haven’t listened to all of the messages, the system beeps five times,and does not delete messages. Delete selected messages Press and ...

Page 11 - FROM A REMOTE TOUCH TONE PHONE

Connect with the Answering System 1 Dial your telephone number from atouch tone phone with a differenttelephone number. 2 When the system answers, enter yourthree-digit Access Code during or afterthe announcement. The systemannounces the number of messages,then beeps twice. If the announcementcontin...

Page 12 - Changing Remote Access Code; Turn System Off; Memory Full

Changing Remote Access Code 1 Press 9 9 . The system announces “ Enter new code. ” 2 Enter your new Remote Access Code(any number between 100 and 999). 3 If a valid code is entered, the systemannounces the new Remote AccessCode. If an invalid code is entered, thesystem beeps five times rapidly, then...

Page 13 - Tapeless Digital; Tapeless Digital

PERF . PERF . fold Tapeless Digital Ans w ering System 1817 Remote Commands T o connect with your answering system: 1 Dial y our telephone n umber fr om a touc h tone phone. 2 When the system ans w er s, enter y our Remote Access Code. The system announces the n umber of messa g es and beeps twice. ...

AT&T 1817 - Manual

Table of Contents:

Summary

Other AT&T Models