Zephyr AK7842ASX Manual - Free PDF Download

Page 3 - INSTALLATION; able of Contents

1 SAFETY NOTICE ................................................................. 2-3 LIST OF MATERIALS ....................................................... 4 INSTALLATION Ducting Calculation Sheet ....................................... 5 Mounting Height & Clearance ............................

Page 4 - Important Safety Notice; READ AND SAVE THESE INSTRUCTIONS

Important Safety Notice READ AND SAVE THESE INSTRUCTIONS 2 www.zephyronline.com WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE. WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Use this u...

Page 5 - WARNING; CAUTION

Important Safety Notice 3 WARNING TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK. CAUTION To reduce risk of fi re and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings,attics, crawl spaces or garages. OPERATION Always leave safety grilles and fi lters ...

Page 6 - List of Materials; PARTS SUPPLIED; HARDWARE PACKAGE CONTENTS

List of Materials 4 www.zephyronline.com MODELS: AK7836ASX, AK7842ASX, AK7848ASX PARTS SUPPLIED 1 - Hood3 - Baffl e fi lters (4 for AK7848ASX)2 - Halogen light bulbs (3 for AK7548ASX) ( pre-installed ) 1 - 10” round transition adapter ( for dual internal and external blowers ) 1 - External blower wi...

Page 8 - DUCTING

Installation – Mounting Height & Clearance 6 www.zephyronline.com DUCTING A minimum of 6” round or 3-1/4” x 10” rectangular duct must be used to maintain maximum air fl ow effi ciency for single blower and 10” round duct for dual, in-line, and external blowers. Always use rigid type metal ducts ...

Page 9 - WARNING FIRE HAZARD; Some Ducting Options; Installation –

7 WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside. Use metal ductwork only. Fasten all connections with sheet metal screws and tape all joints with certifi ed Silver Tape or Du...

Page 10 - CL; ext; top; Marine Grade 316S Body

8 www.zephyronline.com Installation – Speci fi cations 35 15/16 ” (36”) 41 15/16 ” (42”) 47 15/16 ” (48”) 12” *10 ” 27” 4” 18” 1 1/8 ” 8 9/16 ” 13 3/16 ” 2 5/16 ” 6 7/16 ” 2” 2 1/16 ” CL 5 9/16” ext blwr k/o elec k/o 2 11/16 ” top side front 4 5/16 ” *10” transition used with dual, external and in-l...

Page 12 - Turn to page 11 for blower installation

10 www.zephyronline.com C/L C/L A B 12 3/8 ” min30” 4” wood board fig. 2 fig. 1 Installation – Mounting the Range Hood 1. Measure distance from range top to hood bottom ( 30” min ) Level and mark line A. 2. Plum and mark center line.3. Mark mounting height line B. ( 12 3/8” from line A ) ( This is t...

Page 13 - Single Blower; Dual Blower

11 CBI-600B AND PBI-1100A BLOWER INSTALLATION 1. Position blower plate over bracket on inside back of hood and pivot up. Secure plate to hood with (2) 10x3/16” screws. (blower pictured is a PBI-1100A) 2. Connect male end of blower wire to female plug in the hood. (plug is located inside the hood beh...

Page 14 - Remote Blower

12 www.zephyronline.com Installation – Remote Blower Preparation 1. Place 10” round adapter on top of hood and secure with (4) M4x8 screws. Connect 10” round duct work to 10” round adapter. 2. Install threaded end of external blower wiring through external blower wiring knock out located inside the ...

Page 15 - Blower Speed Selection; Switching the rocker switch to middle will turn off the blower.; Features & Controls –

13 Light On/Off By pressing , the light is switched On and Off. is on, is off. Blower Speed Selection The 2 speed levels are selected by switching to for level one and for level two. Lights On/Off Adjust Blower Level (2 Speeds) 1 1 2 2 Switching the rocker switch to middle will turn off the blower. ...

Page 16 - Stainless Steel Baffl e Filters; Replacing Baffle Filters; Maintenance –

14 www.zephyronline.com SURFACE MAINTENANCE: Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent, or steel wool/scouring pads which will scratch and damage surface. Do not use products containing chlorine bleach or orange cleaners. For heavier s...

Page 17 - REPLACING LIGHT BULBS; CAUTION: Light bulb becomes extremely hot when turned on.

15 REPLACING LIGHT BULBS CAUTION: Light bulb becomes extremely hot when turned on. DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. Note: Bulb does not uns...

Page 18 - roubleshooting; TROUBLESHOOTING PROCEDURES FOR CYPRESS; Issue

T roubleshooting 16 www.zephyronline.com TROUBLESHOOTING PROCEDURES FOR CYPRESS Issue Cause What to do After installation, the unit doesn’t work. 1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s power is ON. 2. The power line and the cable locking connector is no...

Page 19 - DESCRIPTION PART #; Replacement Parts; List of Parts and

17 DESCRIPTION PART # Replacement Parts Light Bulb MR16 (GU10) 35W (each) Z0B-0023 Baffl e Filter (each) 50210009 Optional Accessories Single Internal Blower CBI-600B Dual Internal Blower PBI-1100A External Blower CBE-1000 In-Line Blower PBN-1000A Vinyl Cover (36”) AK0636AB Vinyl Cover (42”) AK0642A...