Xilinx ML507 - Manual - manualsarea.com

Page 2 - Overview; Setup

Overview • Setup • Boot with ACE-loader ACE File • Observe LCD and Terminal messages • Load new Configuration • Re-load ACE-loader

Page 4 - Additional Setup Details

Additional Setup Details • Refer to ml505_overview_setup document for details on: – Software Requirements – ML507 Board Setup • Equipment and Cables • Software • Network – Terminal Programs • This presentation requires the 9600-8-N-1 Baud terminal setup Note: Presentation applies to the ML507

Page 5 - Hardware Setup

Hardware Setup • Connect the Xilinx Parallel Cable IV (PC4) to the ML507 board • Connect the RS232 nullmodem cable to the ML507 board Note: Presentation applies to the ML507

Page 6 - Connect a DVI monitor

Hardware Setup • The ML507 uses a DVI videointerface • Connect a DVI monitor or • Use a DVI/VGA adapter to connect a VGA monitor – http://www.belkin.com Note: Presentation applies to the ML507

Page 7 - USB Keyboard

Hardware Setup • USB Keyboard – www.dell.com Note: Presentation applies to the ML507

Page 8 - Factory CompactFlash

Factory CompactFlash • The CompactFlash shipped with the ML507 board has the following ace files preloaded: Note: Presentation applies to the ML507

Page 9 - Verify Factory Default Settings

Verify Factory Default Settings • Set the Ethernet PHY jumpers, J22, J23 to positions 1-2 (1) • Insert the Factory CompactFlash into the ML507 board (2) • Set the Front DIP switches (SW3) to 00010101 (1 = ON) (3) • Set the Rear DIP switches (SW6) to 11001010 (4) • Power-up the ML507 board 4 Note: Pr...

Page 10 - Bootload

Bootload • The bootload_video.ace loads: Note: Presentation applies to the ML507

Page 11 - The terminal window also reflects the bootload application

Bootload • The terminal window also reflects the bootload application • Use the left/center/right buttons to choose an application or type a number in the terminal window • After each demo, push the SysACE reset to return to bootload Note: Presentation applies to the ML507

Page 12 - Slideshow; Type 1, to launch the slideshow application in Configuration 1

Slideshow • Type 1, to launch the slideshow application in Configuration 1 • The slideshow loads the presentation into memory then presents it Note: Presentation applies to the ML507

Page 13 - The slideshow app will present a series of slides on the Monitor:

Slideshow • The slideshow app will present a series of slides on the Monitor: Note: Presentation applies to the ML507

Page 14 - Web Server; Type 2, to launch the web server application in Configuration 2

Web Server • Type 2, to launch the web server application in Configuration 2 – Note: You may need to turn off your browser's proxy and specify a direct connection to the Internet in your browser options Note: Host IP is 192.168.1.1, subnet mask is 255.255.255.0

Page 15 - Running the LWIP Demo

Running the LWIP Demo • Open a web browser to address 192.168.1.10

Page 16 - Click the Toggle LEDs button view change on ML507

Running the LWIP Demo • Click the Toggle LEDs button; view change on ML507

Page 17 - Simon; Type 3, to launch the Simon application in Configuration 3

Simon • Type 3, to launch the Simon application in Configuration 3 Note: Presentation applies to the ML507

Page 18 - Board Diagnostics; Type 4, to launch the XROM application in Configuration 4

Board Diagnostics • Type 4, to launch the XROM application in Configuration 4 Note: Presentation applies to the ML507

Page 19 - XROM includes a series of board test routines

Board Diagnostics • XROM includes a series of board test routines Note: Presentation applies to the ML507

Page 20 - Type 5, to launch the USB Keyboard application in Configuration 5

USB Keyboard • Type 5, to launch the USB Keyboard application in Configuration 5 • Type ML507 and view results: Note: Attach keyboard after demo loads

Page 21 - My ACE; Type 6, to launch the My ACE application in Configuration 6

My ACE • Type 6, to launch the My ACE application in Configuration 6 Note: Presentation applies to the ML507

Page 22 - Ringtone; Type 7, to launch the Ringtone application in Configuration 7

Ringtone • Type 7, to launch the Ringtone application in Configuration 7 • Press any key then press 1-7 to play a simple melody Note: Presentation applies to the ML507

Page 23 - Documentation

Documentation • Virtex-5 – Silicon Devices http://www.xilinx.com/products/silicon_solutions – Virtex-5 Multi-Platform FPGA http://www.xilinx.com/products/silicon_solutions/fpgas/virtex/virtex5 – Virtex-5 Family Overview: LX, LXT, SXT, and FXT Platforms http://www.xilinx.com/support/documentation/dat...

Xilinx ML507 - Manual

Table of Contents:

Summary

Other Xilinx Models