Xantech RT16-10 - Manual
Xantech RT16-10 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – RC68 PROGRAMMER / REMOTE CONTROL; be given to the final user for the following reasons:; APPLICABLE RC68+ BUTTON DESCRIPTIONS
- Page 3 – Remote Control Switchers; Place the; ID CODE SWITCH; Each time you adjust switch; must; remove power from the RT16-10; All 16 IR routes remain on until the GP-OFF command is sent.; CAUTION; must leave; RC68 Programmer
- Page 4 – INSTALLATION; RC68+ Programmer is set to the same number.; Group On command will route to all 15 TV's simultaneously.; device. On the URC and the Smart Pad
- Page 5 – Smart PadTM; Connecting LED Indicators to
1
Remote Control Switchers
Fig. 2
ID Code Switch
INSTALLATION INSTRUCTIONS
RT16-10
ADDRESSABLE INFRARED ROUTER
The RT16-10 is a ONE-IN/SIXTEEN-OUT IR switcher which directs an infrared control signal to any one
of 16 output ports, any combination of ports, or all 16 as a group. You can control large groups of TV
monitors (or any other A/V product) from control locations using Xantech IR Receivers or Smart Pads. Up
to 16 devices may be addressed with one RT16-10. Additional RT-10's can be connected for control of
larger numbers of devices, such as TV monitors in a sports bar, by using different IR code groups on each
unit. The "I" and "G" output ports can drive LED indicators placed at each controlled device location so that
you can see which devices are being addressed at any given time.
O N ( 1 )
O F F ( 0 )
1 2 3 4 5 6
O N
A d d r e s s S w i t c h e s
S i n g l e / M u l t i p l e
R o u t i n g S w i t c h
ON (1) - Multiple
OFF (0) - Single
Contoller Select Switch
ON (1) - CTR16
OFF (0) - RC68+
Fig. 1
Model RT16-10 Addressable IR Router
1 2 3 4 5 6
O N
Factory Installed Jumper.
DATA IN
DATA OUT
2
O G G I
4
O G G I
6
O G G I
8
O G G I
10
O G G I
12
O G G I
14
O G G I
16
O G G I
1
3
5
7
9
11
13
15
I = INDICATOR, O = OUTPUT, G = GROUND, S = SIGNAL
IR RCVR
INPUT
+ 1 2 G G
S
S
POWER
12 VOLTS
1 AMP D.C.
ID CODE SWITCH
I G G O
I G G O
I G G O
I G G O
I G G O
I G G O
I G G O
I G G O
RT16 -10
•
ADDRESSABLE IR ROUTER
FEATURES AND SPECIFICATIONS
•The RT16-10 requires the XANTECH RC68+ (or RC68) Hand Held Programmer codes, set to a matching
IR Code Group, to address 16 ports individually or in any combination of groups.
• GP-ON (group on) and GP-OFF (group off) codes from the RC68+ select and deselect all 16 ports together
as a group.
• The factory preset IR Code Group is 70. It can be installer changed by use of the RC68+ Programmer.
• ID CODE SWITCH. Switches 2 ~ 6 of this 6 position
DIP swtich are reserved for future enhancements.
NOTE: The unit willnot operate with RC68+ IR control
signals unless switches 2~6 are all set to the OFF
psition. Switch 1 selects between single and multiple
routing. OFF = Single Routing, ON = Multiple Routing.
• The DATA IN and DATA OUT modular jacks allow
future cascading enhancements.
• One IR input on a 4-terminal plug-in connector permits connection of any Xantech IR Receiver, Keypad,
Controller, etc.
• An LED, adjacent to the IR RCVR INPUT, flashes when any IR commands are received (not just those
that are RT16-10 specific).
• 16 IR "O" and "G" emitter outputs and 16 "I" and "G" indicator outputs are located on 16 plug-in connectors.
• The "I" and "G" indicator outputs are current limited to 25 mA, allowing the direct connection of an LED
without the need for a current limiting resistor.
• Power Jack: 2.1mm. 12V DC @ 1 Amp. Requires one 782-00 Power Supply for each RT16-10.
• Universal mounting fits 19" racks.
• Dimensions: 19" x 3 1/2" x 1 1/4".
• Weight: 1 lb. 3 oz.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 1 2 3 4 5 6 O N 0 C o n t r o l l e r & A d d r e s s S w i t c h e s O N ( 1 ) O F F ( 0 ) RC68 PROGRAMMER / REMOTE CONTROL The RC68+ (or RC68) Programmer (available separately) contains all the commands necessary to operatethe RT16-10 (see Fig. 3). • You will need it to program universal l...
3 Remote Control Switchers 1 2 3 4 5 6 O N 1 C o n t r o l l e r & A d d r e s s S w i t c h e s O N ( 1 ) O F F ( 0 ) Factory InstalledJumper IR ReceiverInput Connectoron RT16-10 IR RCVR INPUT + 1 2 G G S S Fig. 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 GP-ON GP-OFF C GP-ON GP-OFF RoutingComma...
4 INSTALLATION Fig. 5 illustrates a typical application where an RT16-10 is used to route IR control signals to 15 TV monitors. 1. For this example, it is assumed that Single Routing with Group ON and OFF is required. 2. Since only one RT16-10 is used in the system, the factory preset Code Group 7...
