Xantech CC62 - Manual
Xantech CC62 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – but stays ON; Relay
- Page 3 – Remote Control Switchers; IR RCVR INPUT CONNECTOR; Typical applications for the CC62 are as follows:; Location and Adjustment of
- Page 4 – A Typical Multiroom AV Receiver/Amp A/B Switching System; MAIN ROOM; codes, keep the following items in mind:; RC68+ Programmer Instructions for Code Group setting procedures.
- Page 5 – CONTROLLED COMPONENTS; or; IMPORTANT • • •
1
Remote Control Switchers
INSTALLATION INSTRUCTIONS
CC62
REMOTE RELAY MODULE
Fig. 1
The Model CC62 Remote Relay Module
NO
NC
NO
NC
NO
NC
NO
NC
NO
NC
NO
NC
NO
NC
NO
NC
NO
NC
NO
NC
NO
NC
NO
NC
RELAY
1
RELAY
2
RELAY
3
RELAY
4
RELAY
5
RELAY
6
CC62
REMOTE RELAY MODULE
IR CONFIRM
12 VDC
1A
+12V
GND
GND
IR IN
The CC62 Remote Relay Module consists of six double-pole double-throw relays which are controlled by
way of IR commands from a Xantech RC68+ (or RC68) Programmer. The RC68+ commands are "taught"
to learning devices and passed to the CC62 IR IN (S) and G input terminals via Xantech IR receivers,
keypads, etc. The six relays give "dry contact" closures for a multitude of uses where simple contact
closures are needed. Any combination of one to six relays may be selected and operated in several ways
using the commands from the RC68+ Programmer.
FEATURES AND SPECIFICATIONS
• 6 double-pole double-throw relays rated at 5 Amps. 30 volts DC.
• 2 normally open and 2 normally closed contacts per relay.
• Six 6-terminal screw-type plug-in connectors - one for each of the relays.
• Each relay and the relay poles are isolated from each other allowing use in circuits of differing potentials
and grounds.
• 4-terminal IR IN and +12V plug-in for Xantech IR Receivers, Smart Pads, connecting blocks and other
devices.
• IR Confirm LED lights with RC68+ and non RC68+ IR signals.
• RC68+ IR commands permit Pair, Toggle, Momentary and Group mode operations as well as different
IR codes for use of multiple CC62's.
• The CC62's Code Group number is 60.
• Universal mounting fits 19-inch racks or any 3-1/2" X 19" flat surface. Extends about 2-3/4" behind panel
with cables connected.
• Requires RC68+ (or RC68) Programmer and 782-00 Power Supply.
• Power: 12 VDC @ 300mA.
• Dimensions: 19" W x 3-1/2" H x 2-1/4" D
RC68+ PROGRAMMER / REMOTE CONTROL
The RC68+ Programmer (available separately) contains all commands necessary to operate the CC62 (see
Fig. 2).
• You will need it to program universal learning devices such as the Xantech URC-1 learning remote, the
Xantech Smart Pads, the 590 Controller, the 710 Fone Link, etc., with commands that operate the CC62.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 CC62 • NOTE: The RC68+ codes operate several other Xantech models as well, such as the RS41AV, CC12, ZPR68, etc. Therefore, only the button descriptions that apply to the operation of the CC62 arelisted below. All others should be ignored. CAUTION: While the RC68+ can be used as a handheld remot...
3 Remote Control Switchers CC62 The CC62 should normally be plugged into an unswitched AC outlet. However, if the power to the CC62is interrupted by a power failure or other reason, the internal memory will retain the last selected switchedcondition for each of the relays. IR RCVR INPUT CONNECTOR ...
4 Fig. 4 A Typical Multiroom AV Receiver/Amp A/B Switching System NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC RELAY 1 RELAY 2 RELAY 3 RELAY 4 RELAY 5 RELAY 6 CC62 REMOTE RELAY MODULE IR CONFIRM 12 VDC 1A MAIN ROOM 480-00 Dinky Link ™ IR Receiver S-62/64/66 Wall Speakers...
