Xantech 680-10 - Manual
Xantech 680-10 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – be given to the final user for the following reasons:; APPLICABLE RC68+ BUTTON DESCRIPTIONS; Place the; Outlet; RC68 Programmer
- Page 3 – Remote Control Switchers; INSTALLATION; See the 590 instructions for programming procedures.
- Page 4 – X X; remain on until the last AV receiver is turned OFF.; MOUNTING
1
Remote Control Switchers
INSTALLATION INSTRUCTIONS
.
The Model 680-10 is an IR Remote Controlled AC Switcher with six AC outlet receptacles. It accepts RC68+
(or RC68) IR Programmer commands coming from any Xantech IR receiver, keypad, or controller direct-
wired to its IR Input port. Switching modes of ON, OFF, Toggle, Momentary and Group are possible. Each
outlet is switched ON or OFF by a high current electromechanical relay for higher reliability than solid state
switching methods.
Sequential ON commands for each outlet are possible when used in conjunction with learning devices, such
as Xantech URC-1 remotes, Smart Pads, or 590 controllers.
Since the 680-10 has 30 installer-adjustable IR code groups, it allows multiple 680-10's to be individually
controlled when used in the same system.
RESET
120 VAC
15A MAX
OUTLET 4
5A MAX
OUTLET 5
5A MAX
OUTLET 6
5A MAX
OUTLET 1
5A MAX
OUTLET 2
5A MAX
OUTLET 3
5A MAX
IR
INPUT
CONFIRM
➧
TOTAL LOAD LIMITED TO 15A
TEMPORARY POWER TAP
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
USE INDOORS IN A DRY LOCATION.
680-10
REMOTE AC SWITCHER
Fig. 1
Model 680-10 IR Remote Controlled AC Switcher
680-10
REMOTE AC SWITCHER
FEATURES AND SPECIFICATIONS
• Six AC Outlets rated at 120 VAC, 5 Amps each.
• 15 Amps total current rating.
• Includes 15-Amp circuit breaker.
• 14-Gauge heavy duty 3-conductor power cord, 5-1/2 feet in length, with a grounded 3-prong plug.
• IR input jack (3.5mm mini phone jack)
• An LED indicator lights to confirm the presence and acceptance of 680-10 IR commands.
• Requires RC68+(or RC68) hand-held Programmer codes set to a matching IR code group.
• The 680-10 is factory preset to code group 88.
• Dimensions: 15-1/2" W x 4-1/2" D x 2-3/8" H..
RC68+ PROGRAMMER / REMOTE CONTROL
The RC68+ (or RC68) Programmer (available separately) contains all the commands necessary to operate
the 680-10 (see Fig. 2).
• You will need it to program universal learning devices such as the Xantech URC-1 learning remote, the
Xantech Smart Pads, the 590 Programmable Controller, the 710 Fone Link, etc., with commands that
operate the 680-10.
• NOTE: The RC68+ codes operate several other Xantech models as well, such as the RS41AV, CC12,
ZPR68, etc. Therefore, only the button descriptions that apply to the operation of the 680-10 are
listed in the Button Descriptions section. All others should be ignored.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 680-10 CAUTION: While the RC68+ can be used as a handheld remote control, it is highly recommended it not be given to the final user for the following reasons: • Since it includes adjustable code groups, the user may inadvertently alter the installer configurations. • Also, since the user will r...
3 Remote Control Switchers 680-10 NOTE: The 680-10 should normally be plugged into an unswitched AC outlet. However, if the power tothe 680-10 is turned off by a power failure, or other means, the internal memory will retain the last selectedswitched condition for each of the outlets. INSTALLATION...
4 +12 VDC IR OUT GND 780-10 J-BOX RECEIVER OUT V IR RCVR PWR G S 795-20 Four Zone Amplified Connecting Block Satellite Receiver VCR MAIN ROOM, EQUIPMENT CABINET, ETC. Emitter 291-10 Hidden Link™ IR Receiver GND +12V ZONE 2 780-10 J-Box IR Receiver 3-WireCable GND +12V 480-00 Dinky Link™ IR Receive...
