Page 2 - I n t r o d u c t i o n
2 I n t r o d u c t i o n Gen’l (Rev. 2/19/2008) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manuala...
Page 3 - TABLE OF CONTENTS
I n t r o d u c t i o n 3 MAN0357 (Rev. 12/10/2007) TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY RULES . ....
Page 4 - SPECIFICATIONS
4 I n t r o d u c t i o n MAN0357 (Rev. 1/5/2007) SPECIFICATIONS VR48A VR66A VR73A VR84A Drum Width 48 inches (129 cm) 66 inches (168 cm) 73 inches (186 cm) 84 inches (215 cm) Drum Diameter 23 inches (59 cm) 23 inches (59 cm) 23 inches (59 cm) 23 inches (59 cm) Drum Oscillation ±7.5° ±7.5° ±7.5° ±7....
Page 5 - S a f e t y; INSTALLATION; SAFETY RULES
S a f e t y 5 Alitec Vibratory Roller Safety Rules (Rev. 1/5/2007) INSTALLATION Hydraulics must be connected as instructed in thi s ma nual . Do not s ubs titute parts , modi fy, orconnect in any other way. After connecting hoses, check that all control lever positions function as instructed in ...
Page 6 - OPERATION
6 S a f e t y Alitec Vibratory Roller Safety Rules (Rev. 1/5/2007) (Safety Rules continued from previous page) Always wear relatively tight and belted clothing t o a v o i d g e t t i n g c a u g h t i n m o v i n g pa r ts . We a rs tu rdy, r o u gh -s o l e d wo r k s h oe s a nd p rot e c ti v ...
Page 7 - MAINTENANCE
S a f e t y 7 Alitec Vibratory Roller Safety Rules (Rev. 1/5/2007) MAINTENANCE Before leaving operator's seat, lower lift arms and put attachment on the ground. Engage brake,stop engine, remove key, and remove seat belt. NEVER GO UNDERNEATH EQUIPMENT. Never place any part of the body underneath ...
Page 8 - TO AVOID SERIOUS INJURY OR DEATH:; WARNING; WARNING; See exploded view drawing on page 16 for decal locations.; SAFETY & INSTRUCTIONAL DECALS; Replace Immediately If Damaged!
8 S a f e t y MAN0357 (Rev. 12/10/2007) MODEL NO. SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. 30 - Serial Number Plate TO AVOID SERIOUS INJURY OR DEATH: Read attachment and power unit manuals before you use, service, or repair machine. Follow all safety rules and instructions. (Manua...
Page 9 - O p e r a t i o n; ATTACHING TO LOADER; TO COMPACT
O p e r a t i o n 9 MAN0357 (Rev. 12/10/2007) OPERATION The Vibratory Roller is a hydraulically powered attach-ment intended to compact soil, stone, or fill material.The performance of the attachment can vary greatlydepending on how it is used and operated. Therefore,the recommended operating proced...
Page 10 - O w n e r S e r v i c e; OWNER SERVICE
1 0 O w n e r S e r v i c e MAN0357 (Rev. 12/10/2007) OWNER SERVICE ■ Before performing any maintenance or service on the unit, perform the mandatory safety shut-down procedure. MAINTENANCE Proper maintenance of the attachment will result inlonger life and more productive and cost effective oper-ati...
Page 11 - INNER BEARING REPLACEMENT; OUTER BEARING REPLACEMENT
O w n e r S e r v i c e 11 MAN0357 (Rev. 12/10/2007) Figure 2 4. Remove the shaft nut (13, using part number1023106 socket), the shaft washer, and thetongued washer (27), Figure 3. Figure 3 5. Pull the inner bearing housing (9) from the shaft,Figure 4. Figure 4 6. Remove the outer bearing housing mo...
Page 12 - BEARING INSTALLATION
1 2 O w n e r S e r v i c e MAN0357 (Rev. 12/10/2007) BEARING INSTALLATION 1. Apply a small amount of lubrication (oil or grease)to the outer bearing housing. 2. Assemble the outer bearings to the inner bearingsusing an industrial press. Figure 6 3. Install one of the housing assemblies to the shaft...
Page 14 - NOTES
1 4 O w n e r S e r v i c e MAN0357 (Rev. 12/10/2007) NOTES
Page 15 - Tr o u b l e s h o o t i n g / D e a l e r S e r v i c e; TROUBLESHOOTING; SAFETY DECALS
Tr o u b l e s h o o t i n g / D e a l e r S e r v i c e 1 5 MAN0357 (Rev. 12/10/2007) TROUBLESHOOTING DEALER SERVICE Although the Alitec attachment is supplied fully assem-bled, some simple checks should be performed before operation begins. SAFETY DECALS The safety decals existing on the attachmen...
Page 16 - P a rts; VIBRATORY ROLLER GENERAL ASSEMBLY
1 6 P a rts MAN0357 (Rev.12/10/2007) VIBRATORY ROLLER GENERAL ASSEMBLY REF PART QTY DESCRIPTION 1 105382 1 Chassis weldment, VR48A 1 105373 1 Chassis weldment, VR66A 1 105374 1 Chassis weldment, VR73A 1 105420 1 Chassis weldment, VR84A 2 102089 1 Attach frame, VR48A 2 101528 1 Attach frame, VR66A 2 ...
Page 17 - P a r ts
P a r ts 1 7 MAN0357 (Rev. 12/10/2007) VIBRATORY ROLLER GENERAL ASSEMBLY REF PART QTY DESCRIPTION 4 101711 1 Drum weldment, 48" VRA Smooth 4 101434 1 Drum weldment, 66" VRA Smooth 4 101444 1 Drum weldment, 73" VRA Smooth 4 102832 1 Drum weldment, 84" VRA Smooth 4 101712 1 Drum weldme...
Page 18 - OPTIONAL FLOW CONTROL KITS
1 8 P a rts MAN0357 (Rev.12/10/2007) OPTIONAL FLOW CONTROL KITS REF PART QTY DESCRIPTION 1 1007693 1 Priority flow 17 gpm (used in kit 1012103) 1 1007694 1 Priority flow 23 gpm (used in 1012104) 2 1007695 1 Priority flow block 3 1012100 1 Guard, valve VRA 4 F1025 1 Fitting, 8 OM x 8 FLM 90° 5 316017...
Page 19 - A p p e n d i x; BOLT TORQUE CHART
A p p e n d i x 1 9 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...
Page 20 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM
2 0 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............
Page 21 - WARRANTY
F-3079 (Rev. 5/15/2008) WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Information Below and Save for Future Reference. Date Purchased: ____________________________ From (Dealer): ___________________________________________ Model Nu...
Page 22 - (Replacement Parts For All Models Except Mow’n Machine
F-8494 (Rev. 6/23/2005) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com ©2004 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trade...
