Woods T5060 - Manual - manualsarea.com

Page 2 - I n t r o d u c t i o n

2 I n t r o d u c t i o n LMK (Rev. 7/20/2007) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Loader Operator’sMan...

Page 3 - S a f e t y; INSTALLATION; SAFETY RULES

S a f e t y 3 Loader Mounting Kit SR3 (4/25/2003) INSTALLATION This Loader Mounting Kit is to be used only for the loaders and tractors specified in this manual.Any other use or modification of this mounting kitmay result in serious injury or death. Hydraulics must be connected as instructed in ...

Page 4 - M o u n t I n s ta l l a t i o n; LOADER MOUNT INSTALLATION; CAUTION; Tractor Preparation

4 M o u n t I n s ta l l a t i o n MAN0788 (1/16/2009) LOADER MOUNT INSTALLATION ■ Only use this mounting kit for mounting Woods LUP126-2, LUP132-2 loaders on New Holland ® T5040, T5050, T5060, T5070 2WD & FWA tractorsand Case IH ® Farmall ® 85U, 95U and 105U 2WD & FWA tractors. Any other us...

Page 5 - Install Right and Left Mid-Mounts

M o u n t I n s ta l l a t i o n 5 MAN0788 (1/16/2009) Install Right and Left Mid-Mounts NOTE: Use an overhead lifting device capable of lift- ing mount. Slide strap through loader mounting holeand cinch (Figure 1). Mount should be balanced andhang straight. 1. Attach right mount to loader ready bra...

Page 6 - Install Optional Grill Guard

6 M o u n t I n s ta l l a t i o n MAN0788 (1/16/2009) Install Optional Grill Guard 1. Attach grill guard support bracket (A) to the frontof the tractor using four cap screws (K), hardenedflat washers (G), two spacers (C) and hex nuts (L) 2. Attach grill guard (B) to support bracket (A) usingtwo (on...

Page 7 - H y d r a u l i c I n s ta l l a t i o n; HOSE KIT INSTALLATION; WARNING; General Description

H y d r a u l i c I n s ta l l a t i o n 7 MAN0788 (1/16/2009) HOSE KIT INSTALLATION Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety goggles.Hydraulic fluid under pressure can easily penetrateskin and will cause ...

Page 8 - Install Fittings and Hoses

8 H y d r a u l i c I n s ta l l a t i o n MAN0788 (1/16/2008) 1028835 Hose Kit Install Fittings and Hoses Install Hydraulic Fitting, Control Valve Install four adapters (4 or 5), elbows (8), coloredbands (9-12), dust plugs (13) and female quick cou-plers (6) into the control valve located under the...

Page 9 - Secure Hoses; Verify Control Movements

H y d r a u l i c I n s ta l l a t i o n 9 MAN0788 (1/16/2009) 1028835 Hose Kit Secure Hoses Secure hoses to the back of right loader upright usingplastic tie as shown in Figure 9. Do not cinch hoses tight, they need to move with theloader during operation. Figure 9 . Secure Hoses Verify Control Mov...

Page 10 - Connect and Route Hoses

1 0 H y d r a u l i c I n s ta l l a t i o n MAN0788 (1/16/2008) 58025 HOSE KIT General Description These set-up instructions are for operating theLUP126-2 or LUP132-2 loader using the tractorhydraulic rear remote control couplers. To use thishydraulic connection, the tractor must be equippedwith tw...

Page 11 - Install Hose Brackets

H y d r a u l i c I n s ta l l a t i o n 11 MAN0788 (1/16/2009) 58025 Hose Kit Install Hose Brackets 1. Remove right rear rockshaft housing cap screwand attach hose guide (5) as shown in Figure 13.Secure using tractor hardware. 2. Attach hose support (4) to right side of transmis-sion housing using ...

Page 12 - Verification of Control Movements

1 2 H y d r a u l i c I n s ta l l a t i o n MAN0788 (1/16/2008) 58025 Hose Kit Verification of Control Movements 1. Mount loader to tractor: Remove mount pins from loader uprights. Align tractor with loader andslowly drive tractor into loader. Shut off tractor. 2. Connect loader feedline hoses to t...

Page 13 - P a r ts

P a r ts 1 3 MAN0788 (1/16/2009) 2300012 LOADER MOUNTING KIT REF PART QTY DESCRIPTION 1 1026397 1 Left oscillation stop 2 1026398 1 Right oscillation stop 3 1028920 1 Right rear mount 4 1028921 1 Left rear mount 10 1006371 20 3/4 Hardened flat washer, extra thick 11 1028950 4 M20 x 2.5P x 80 mm HHCS...

Page 14 - P a rts

1 4 P a rts MAN0788 (1/16/2009) 1028835 HOSE KIT NOTE: Not all parts supplied with this hose kit are used for this application. REF PART QTY DESCRIPTION 3 1009513 4 Hose, 76" x 3/8 NPTM x 3/4 JICM 4 1010920 4 Adapter, M22 x 1.5M x 3/4 JICM 5 1012055 4 Adapter, M18 x 1.5M x 3/4 JICM 6 64299 4 Qui...

Page 16 - A p p e n d i x; BOLT TORQUE CHART

1 6 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...

Page 17 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM

A p p e n d i x 1 7 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............

Page 18 - WARRANTY

F-3079 (Rev 11/24/2008) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 USA 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Informa...

Page 19 - (Replacement Parts For All Models Except Mow’n Machine

F-8494 (Rev. 6/23/2005) WARRANTY (Replacement Parts For All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material andworkmanship for a period of ninety (90) days from the date...

Woods T5060 - Manual

Table of Contents:

Summary

Other Woods Models