Page 2 - I n t r o d u c t i o n
2 I n t r o d u c t i o n Gen’l (Rev. 3/5/2010) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manualar...
Page 3 - TABLE OF CONTENTS; Si no lee Ingles, pida ayuda a
I n t r o d u c t i o n 3 MAN0101 (Rev. 9/15/2006 TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 GENERAL INFORMAT...
Page 4 - I n t r o d u ct i o n; SPECIFICATIONS; GENERAL INFORMATION; WARNING
4 I n t r o d u ct i o n MAN0101 (Rev. 9/15/2006) SPECIFICATIONS Super Turf Renovator STR48S STR60S STR72S Working Width 47" 59" 71" Overall Width 58" 70" 82" Roller Pins 1/2" x 1-3/4" 1/2" x 1-3/4" 1/2" x 1-3/4" Bearing (Self-Aligning) Six 1" Six ...
Page 5 - S a f e t y; TRAINING; SAFETY RULES
S a f e t y 5 STR48-72 Safety Rules (Rev. 7/28/2005) TRAINING Safety instructions are important! Read all a t ta c h m e n t a n d p o w e r u n i t m a n u a l s ; f o l l o w a l lsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer. To...
Page 6 - MAINTENANCE
6 S a f e t y STR48-72 Safety Rules (Rev. 7/28/2005) (Safety Rules continued from previous page) Watch for hidden hazards on the terrain during operation. Stop power unit and equipment immediately u p o n s t r i k i n g a n o b s t r u c t i o n . Tu r n o f f e n g i n e ,remove key, inspect, ...
Page 7 - Use a clean, damp cloth to clean safety decals.; SHIELD MISSING; ROTATING COMPONENTS; SAFETY & INSTRUCTIONAL DECALS; Replace Immediately If Damaged!
S a f e t y 7 MAN0101 (Rev.9/15/2006) 6 - PN 20106 Red Reflector 3 - Serial Number Plate BE CAREFUL! Use a clean, damp cloth to clean safety decals. Avoid spraying too close to decals when using a pressure washer; high-pressure water canenter through very small scratches or under edges of decals cau...
Page 8 - S a fe t y
8 S a fe t y MAN0101 (Rev. 9/15/2006) SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 2 - PN 55122 1 - PN 55121 7 - PN 1003751 WARNING 55121--C FALLING OFF CAN RESULT IN BEING RUN OVER. Tractor must be equipped with ROPS (or ROPS ...
Page 9 - O p e r a t i o n; OPERATION; Super Turf Renovator Roller Operation; CAUTION
O p e r a t i o n 9 MAN0101 (Rev. 9/15/2006) OPERATION The operator is responsible for the safe operation ofthis renovator. The operator must be properly trained.Operators should be familiar with the equipment, thetractor, and all safety practices before starting opera-tion. Read the safety rules an...
Page 10 - Operation; Attach Super Turf Renovator to Tractor
1 0 O p e r a t i o n MAN0101 (Rev. 9/15/2006) adjusted to deliver the desired down pressure androller action and achieve the desired seedbed appear-ance. When the situation permits, making a second pass 90-degrees to the first is an effective way for the roller pinsto penetrate areas where uneven s...
Page 11 - Adjust Front Roller Angle; Seeding Operation
O p e r a t i o n 11 MAN0101 (Rev. 9/15/2006) Adjust Front Roller Angle 1. Position tractor and renovator on a level surface. 2. Raise renovator slightly off the ground. 3. Stop engine and set parking brake. 4. Remove klik pin (21), lock pin (15), and lockassembly (5) from front of renovator. See Fi...
Page 12 - Operating Tips; IMPORTANT; Pre-Operation Check List
1 2 O p e r a t i o n MAN0101 (Rev. 9/15/2006) Operating Tips IMPORTANT ■ Before closing down the cup (reducing rates), the operator should make certain that the cups arenot full of seed. If cups are full of seed (especiallysmall, round, hard seed), it may be necessary tocover the meter holes and ru...
Page 13 - O p e ra t i o n
O p e ra t i o n 1 3 MAN0101 (Rev. 9/15/2006) E quipme n t Y ou wil l n eed the fol low ing equ ip men t to c a lib ra te y o u r see der . 1. T w o ja ck s tand s. 2. O ne t o two pou nd sam p le of se ed. 3. O ne t a rp or c anv as ap pr ox im atel y 48" x 84" . 4. O ne s c a le c a p a b ...
Page 14 - O w n e r S e r v i c e; OWNER SERVICE; Lubrication Information
1 4 O w n e r S e r v i c e MAN0101 (Rev.9/15/2006) OWNER SERVICE The information in this section is written for operatorswho possess basic mechanical skills. If you need help,your dealer has trained service technicians available.For your protection, read and follow the safety informa-tion in this m...
Page 15 - A ss e mb l y; ASSEMBLY; DEALER SET-UP INSTRUCTIONS
A ss e mb l y 1 5 MAN0101 (Rev.10/15/2004) ASSEMBLY DEALER SET-UP INSTRUCTIONS Assembly of this equipment is the responsibility of theWoods dealer. It should be delivered to the owner com-pletely assembled, lubricated, and adjusted for normaloperating conditions. In most cases the Super Turf Renovat...
Page 16 - A s s e m b l y; Install Roller Chains
1 6 A s s e m b l y MAN0101 (Rev.10/15/2004) Figure 14 . Idler Bracket Assembly Installed Install Roller Chains 1. Place roller chain (A - 35 link) around the seed boxsprocket and the large inner sprocket on the idlerbracket assembly. Secure chain using master link. 2. Install roller chain (B - 28 l...
Page 18 - P a rts
1 8 P a rts MAN0101 (Rev. 9/15/2006) STR48S-2, STR60S-2 & STR72S-2 MAIN ASSEMBLY
Page 19 - P a r ts
P a r ts 1 9 MAN0101 (Rev. 9/15/2006) STR48S-2, STR60S-2 & STR72S-2 MAIN ASSEMBLY PARTS LIST REF STR 48-2 STR 60-2 STR72-2 QTY DESCRIPTION 1 ………… ………… ………… 1 STR Frame 2 1000778 1000778 1000778 1 Rear roller arm, right 3 1000779 1000779 1000779 1 Rear roller arm, left 4 D2213 D2213 D2213 4 Bushi...
Page 24 - A p p e n d i x; BOLT TORQUE CHART
2 4 A p p e n d i x Bolt Torque & Size Charts (Rev. 10/10/2005) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual ...
Page 25 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM
A p p e n d i x 2 5 Bolt Torque & Size Charts (Rev. 10/10/2005) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG ............................................................. Agriculture ATF ...............
Page 26 - WARRANTY; (Replacement Parts For All Models Except Mow’n Machine; Zero-Turn Mowers and Woods Boundary
F-8494 (Rev. 6/23/2005) WARRANTY (Replacement Parts For All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material andworkmanship for a period of ninety (90) days from the date...
